新版中兴F673AV9 TTL登陆
最近入手了一个F673A V9的移动光猫。看中的是性能够用，发热低，个头小，价格便宜等优点。这个SOC也远比MTK那个烂大街的EN7625看着舒服。
移动的猫玩起来比较简单，大多数地区都是默认超密，这个猫也可以网页修改GPON SN和password。还支持电信常用LOID注册，基本上可以通用了。
硬件信息如下
CPU: ZX279128S@A9,1000MHZ
Board: ZTE zx279128sevb
I2C: ready
5DRAM:512 MiB
2.4G MT7603E
5G MT7612E(有散热片就没扒开了，一般也不会用别的)
没有外置功放
唯一不爽的是默认TELNET关闭，也不像旧猫可以切默认地区，SSID也没法去掉CMCC前缀。
试着用加了TTL，中断也正常，可是不像其他的猫有登陆的地方，所以常用的指令也用不上，不知道是不是阉割了，有了解的大神请指点下。
拆机图就暂时不发了，嫌麻烦，TTL输出如下：
U-Boot 2013.04 (Jul 27 2019 - 18:46:21)
CPU: ZX279128S@A9,1000MHZ
Board: ZTE zx279128sevb
I2C: ready
5DRAM:512 MiB
5,20000000,60000000
product_vid = 3
vid=3-F673AV9
mtk reset,64,53
mtk reset,65,55
bootsel=3
NAND:manuid=c8,a
Manu ID: 0xc8, Chip ID: 0x0a (ESMT SPI NAND F50L2G41LB 256MiB 3,3V)
256 MiB
<nand_read_skip_bad_,333>!mtdpart=0x1,offset=0x0,mtdpartoffset=0x180000,mtdPartsize=0x80000,length=0x20000
In: serial
Out: serial
Err: serial
clk_pll env is not setted, core clk won't change
Net: enter ref_clk_set.. mode = 0 .
enter pll_cfg_fractional
ref_clk_set success!
gpon serdes init
rxpll_ready
addr 0x9400004c before value is 38000
addr 0x9400004c after value is 381ff
eth0
Hit 1 to upgrade software version
Hit any key to stop autoboot:0
=> ?
? - alias for 'help'
autorun - start version
base - print or set address offset
bdinfo- print Board Info structure
boot - boot default, i.e., run 'bootcmd'
bootd - boot default, i.e., run 'bootcmd'
bootk - boot kernel
bootm - boot application image from memory
bootz - boot Linux zImage image from memory
cmp - memory compare
coninfo - print console devices and information
cp - memory copy
dhcp - boot image via network using DHCP/TFTP protocol
downver - upgrade software downloaded from TFTP server
echo - echo args to console
fdt - flattened device tree utility commands
go - start application at address 'addr'
gpiotest- gpiotest dir
gpiotest value
gpiotest gvalue
help - print command description/usage
i2c - I2C sub-system
imxtract- extract a part of a multi-image
itest - return true/false on integer compare
md - memory display
mii - MII utility commands
mt - memory test
mtddebug- mtddebug operate
mtest - simple RAM read/write test
mw - memory write (fill)
nand - NAND sub-system
ping - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
reset - Perform RESET of the CPU
run - run commands in an environment variable
saveenv - save environment variables to persistent storage
setenv- set environment variables
sleep - delay execution for some time
tftp - boot image via network using TFTP protocol
version - print monitor, compiler and linker version
watchdog- watchdog reset && disable
xmodem- xmodem
=> <INTERRUPT> 除了工具，啥办法也没有配置这个猫 这是中断早了进到uboot里面了 qiner_1984 发表于 2020-4-17 19:06
这是中断早了进到uboot里面了
是的，ZTE新出的机器启动固件以后，TTL里就没东西了玩了。
目前总结下来要么工具开telnet，要么从配置文件下手，都不容易 走走看看学习一下，谢谢分享 手上同样中兴新光猫,现在只能坐等大神们推广,淘宝已经可以刷,应该很快会公布了 谢谢，楼主无私的分享你的宝贵的经验，顺便来赚个猫粮 楼主，用CMCCAdmin登录后，GPON SN和password那里是灰的，请问怎么修改啊？ 谢谢分享