请师傅们看一下这是什么问题
本帖最后由 qiner_1984 于 2020-3-12 22:04 编辑Chip Type is SD5117M
safetycode boot type: nand flash
Safetycode build: (V500R019C00 Jun2 2018 - 20:18:07)
Select startcodeA
startcode start at 0x20020088
Startcode 2017.07 (V500R019C00 Jun 02 2018 - 20:18:45 +0800 V5)
NAND:Nand ID: 0xC2 0xDA 0x90 0x95 0x06 0x00 0x00 0x00
ECC Match pagesize:2K, oobzie:64, ecctype:8bit
Nand(Hardware): startcode select the uboot to load
the high RAM is :8080103c
startcode uboot boot count:-562841653
use the main slave_param area from flash, the RAM data is not OK!!!
Use the AllsytemA to load first
Start in Normal Mode
Use the AllsytemA to load success
U-Boot 2017.07 (V500R019C00 Jun 02 2018 - 20:18:27 +0800 V5)
DRAM:256 MiB
Wrong Boot Type
Chip Type is SD5117M
NAND:Special Nand id table Version 1.23
Nand ID: 0xC2 0xDA 0x90 0x95 0x06 0x00 0x00 0x00
ECC Match pagesize:2K, oobzie:64, ecctype:8bit
Nand(Hardware): Block:128KB Page:2KB Chip:268435456B OOB:64B ECC:8bit
256 MiB
256 MiB
Using default environment
In: serial
Out: serial
Err: serial
Net: PHY power down !!!
Mbist flag = 0x0, ddr totoal size = 0x10000000
::CRC:0x3d80a8b4, Magic1:0x5a5a5a5a, Magic2:0xa5a5a5a5, count:0, CommitedArea:0x0, Active:0x0, RunFlag:0x0
Start from main system(0x0)!
CRC:0x3d80a8b4, Magic1:0x5a5a5a5a, Magic2:0xa5a5a5a5, count:1, CommitedArea:0x0, Active:0x0, RunFlag:0x0
Main area: Cert partition Found
Slave area: Cert partition Found
Main area (A) is OK!
CRC:0x93e83925, Magic1:0x5a5a5a5a, Magic2:0xa5a5a5a5, count:1, CommitedArea:0x0, Active:0x0, RunFlag:0x0
Bootcmd:nand read 0x80907f6c 0x267000 0x1bc000; bootm 0x80907fc0
BootArgs:noalign mem=247M flashsize=0x10000000 console=ttyAMA1,115200 root=/dev/mtdblock2 rootflags=image_off=0x223094 rootfstype=squashfs mtdparts=hinand:0x100000(bootcode)raw,0x100000(bootpara)raw,0x3700000(allsystemA)raw,0x3700000(allsystemB)raw,0x8f00000(ubilayer),-(reserved) ubi.mtd=4 maxcpus=0 l2_cache=l2x0 coherent_pool=4M user_debug=0x1f panic=1 skb_priv=192 debug_ll=on
U-boot Start from NORMAL Mode!
NAND read: device 0 offset 0x267000, size 0x1bc000
1818624 bytes read: OK
## Booting kernel from Legacy Image at 80907fc0 ...
Image Name: Linux-3.10.53-HULK2
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1814888 Bytes = 1.7 MiB
Load Address: 80e08000
Entry Point:80e08000
Match the dtb file index : 3!
Memory Start: 80900000
XIP Kernel Image ... OK
kernel loaded at 0x80908000, end = 0x80ac03ca
Starting kernel ...
Uart base = 0x1010F000
dtb addr = 0x80F633D8
Uncompressing Linux...
hs8545m5一直在启动内核的地方循环，已经换了一个同样光猫的flash也一样
这字体,眼都看瞎了... 估计这光猫集成的内存颗粒坏了
页:
[1]