jingjingo 发表于 2019-11-17 09:38:22

中兴F1855 求助

U-Boot 2013.04 (Dec 21 2018 - 19:45:40)

CPU: ZX279121@A9,800MHZ
Board: ZTE zx279121evb
DRAM:512 MiB
product_vid = 9
vid=9-F1855
NAND:manuid=c8,d1

Manu ID: 0xc8, Chip ID: 0xd1 (ESMT SPI NAND GD5F1GQ4UBYIG128MiB 3,3V)
128 MiB
<nand_read_skip_bad_,1253>!mtdpart=0x1,offset=0x0,mtdpartoffset=0xc0000,mtdPartsize=0x40000,length=0x20000
In:    serial
Out:   serial
Err:   serial
Net:   eth0

Hit 1 to upgrade software version
Hit any key to stop autoboot:2  1  0

Cpu temperature is 42 C
addr=1d00000
addr=4500000
select=0x0
search=0x2
<nand_read_skip_bad_,1253>!mtdpart=0x6,offset=0x0,mtdpartoffset=0x100000,mtdPartsize=0x80000,length=0x1000
tmp=0x00000000, value=0
select = 0x0
search->result.entry=1d00140
<nand_read_skip_bad_,1253>!mtdpart=0x2,offset=0x0,mtdpartoffset=0x1d00000,mtdPartsize=0x2800000,length=0x1a1fc60
<nand_read_skip_bad_,1253>!mtdpart=0x0,offset=0x0,mtdpartoffset=0x0,mtdPartsize=0xc0000,length=0x80000
lseek=0x83048000
cmdline=U-Boot V1.0.8P1T7 20181221201639
## Booting kernel from Legacy Image at 85000140 ...
   Image Name:   Linux Kernel Image
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    27392731 Bytes = 26.1 MiB
   Load Address: 80008000
   Entry Point:80008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK
----------------------
|-->setup versioninfo tag...

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
pppppppp

TTL信息到PPPP这里就停住了 但是光猫工作正常~

谁有办法 进入正常的 管理界面~！~

邪恶海盗 发表于 2019-11-17 12:24:33

SDN,基本没啥好玩的...

zabbin 发表于 2019-11-17 12:43:09

我过来看热闹的啊

jingjingo 发表于 2019-11-17 19:52:33

@setttt 谢谢大神~有固件可以刷成HGU吗~

jingjingo 发表于 2019-11-18 17:13:14

@setttt大神能否 我把猫发你 你帮我刷成HGU的固件我想用这个猫的无线~   

k0l 发表于 2019-11-18 20:26:16

我没这个猫不会

jingjingo 发表于 2019-11-19 00:28:12

@setttt 嗯等你有空再说~

pzitw 发表于 2019-12-16 22:01:39

楼主,能发个140W-P怎么备份和恢复分区文件的教程啊.谢谢
页: [1]
查看完整版本: 中兴F1855 求助