zhang260gt 发表于 2020-10-24 05:38:11

/*..............
System start ...
.............*/

U-Boot 1.1.4 (Jul 31 2013 - 16:25:21)

U-Boot code: 90500000 -> 9051FC94BSS: -> 9054658C
RAM Configuration:
Bank #0: 90000000 64 MB
Flash: 16 MB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial

Extend LSW IS AR8316
Initialize broadcast table ... ok
CPURTx Driver For Pilot <Board-A>!
### JFFS2 loading 'fsok' to 0x904bfe84
Scanning JFFS2 FS: . done.
### JFFS2 load complete: 2 bytes loaded to 0x904bfe84
ui_board_id = 3061
::Magic1:0x271116a1, magic2 0x601f2214, count 805962290, flag 1241854102, MainAreaOK 1430555698, slaveAreaOK -1525485032
Start from normal system!
Magic1:0x5a5a5a5a, magic2 0xa5a5a5a5, count 0, flag 0
Addr:0x0,Addr:0x40000,Addr:0x41000,Addr:0x60000,Addr:0x1e0000,Addr:0xae0000,Addr:0xe60000
Start copy data from 0x201e0054 to 0x91000000 with sizeof 0x00865040 ....................Done!
Start system with ram disk and set bootcmd to
BootArgs:noalign mem=50M console=ttyAMA0,115200 root=/dev/ram0 rootfstype=squashfs mtdparts=hisilicon:0x40000(boot)ro,0x1000(flashcfg)ro,0x1f000(syspara)ro,0x180000(krnl)ro,0x8fffac@0x1e0054(rootfs)ro,0x248fe0@0xc17020(minisystem)ro,0x180000(jffs2cfg),-(reserved) user_debug=0x1f panic=1
-----------这里就没有按D键提示！！！
U-boot Start from NORMAL Mode !
## Booting image at 20060054 ...
   Image Name:   Linux-2.6.21.7-hrt1
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1456776 Bytes =1.4 MB
   Load Address: 90008000
   Entry Point:90008000
   Loading Kernel Image ... OK
## Loading Ramdisk Image at 91000000 ...

jocko 发表于 2020-12-23 09:46:15

allensunshine 发表于 2021-1-17 08:34:31

备注一下看看

popjake 发表于 2021-1-17 09:04:27

砖机已处理。

九州震旦 发表于 2022-2-26 17:40:53

看看，有没有真货

狙击手0708 发表于 2022-4-2 12:20:21

拿点猫粮学习一下

yllgfywan 发表于 2022-4-11 23:31:32

没意义，送猫粮

Ginanger 发表于 2022-8-19 08:16:52

回复拿点猫粮

abo990 发表于 2022-8-19 10:07:12

送猫粮了

uin 发表于 2022-9-9 10:31:12



就送点猫粮吧！不过也是个办法！
页: 1 2 [3] 4
查看完整版本: HG8245 TTL不能中断和输入的问题解决