Pauljiang 发表于 2019-3-27 13:46
V5,C5 ，S5 很多人改光模式变成砖头，然后拿咸鱼骗钱。 19版本的猫，按照之前的方法改，1改2,2改1变砖， ...
老姜 此光猫怎么改成电信能用？
或者 改成loid注册？
sd86 发表于 2019-5-22 13:01
请问楼主 HS8546v5电信可以用吗
电信版8145v5，移动版8546v5，联通版8346v5，硬件都是一样的，换壳产品
我的8145v5接ttl一直不显示，不知道为何。。哪里需要做什么设置吗?,谢谢
有刷回来的吗？指教下
Pauljiang 发表于 2019-3-27 13:46
V5,C5 ，S5 很多人改光模式变成砖头，然后拿咸鱼骗钱。 19版本的猫，按照之前的方法改，1改2,2改1变砖， ...
8145V5的G改E变砖，ttl有输出，但后面好像是因为读取什么失败而启动失败。这样有救吗？因为我朋友那边是E网，我这边是G网，我想给他用，就这样了
Pauljiang 发表于 2019-3-27 13:46
V5,C5 ，S5 很多人改光模式变成砖头，然后拿咸鱼骗钱。 19版本的猫，按照之前的方法改，1改2,2改1变砖， ...
你好，今天我也掉坑了，v5,改光模式成砖了，请教怎么救砖？
Pauljiang 发表于 2019-3-27 13:46
V5,C5 ，S5 很多人改光模式变成砖头，然后拿咸鱼骗钱。 19版本的猫，按照之前的方法改，1改2,2改1变砖， ...
HS8145V5刷机后E变成了G，改双模无用，再改E，然后变砖了。
TTL走了一大堆，最后提示，无法接收任何指令，请问大神如何解决？
telnet port:23
telnet: can't connect to remote profile close core dump
Press any key to get started
TCP: Hash tables configured (established 4096 bind 4096)
TCP: reno registered
UDP hash table entries: 256 (order: 1, 12288 bytes)
UDP-Lite hash table entries: 256 (order: 1, 12288 bytes)
NET: Registered protocol family 1
PCI: CLS 0 bytes, default 64
squashfs: version 4.0 (2009/01/31) Phillip Lougher
jffs2: version 2.2. 漏 2001-2006 Red Hat, Inc.
fuse init (API version 7.22)
msgmni has been set to 983
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
brd: module loaded
mtdoops: mtd device (mtddev=name/number) must be supplied
Spi id table Version 1.22
Special nand id table Version 1.33
Hisilicon Flash Memory Controller V100 Device Driver, Version 1.0
flash_type = 0x6
SPI_NAND_FLASH_TYPE
Nand ID: 0xC2 0x12 0xC2 0x12 0xC2 0x00 0x00 0x00
ECC Match pagesize:2K, oobzie:64, ecctype:8bit
Nand(Hardware): Block:128KB Page:2KB Chip:128MB OOB:64B ECC:8bit
NAND device: Manufacturer ID: 0xc2, Chip ID: 0x12 (Macronix MX35LF1GE4AB), 128MiB, page size: 2048, OOB size: 64
NAND_ECC_NONE selected by board driver. This is not recommended!
raw_mtd: treat mtd0 as raw mtd.
2 cmdlinepart partitions found on MTD device hinand
Creating 2 MTD partitions on "hinand":
0x000000000000-0x000000100000 : "bootcode"
0x000000100000-0x000008000000 : "ubilayer_v5"
softdog: Software Watchdog Timer: 0.08 initialized. soft_noboot=0 soft_margin=60 sec soft_panic=0 (nowayout=0)
TCP: cubic registered
NET: Registered protocol family 17
ThumbEE CPU extension supported.
mapp kbox ddrram_address=0, ddrram_size=0 fail:Kbox device descriptor struct kbox_dev_des Intialization Failed
kbox: init ddrram fail ret=-99
kbox: load OK
UBI: attaching mtd1 to ubi0
UBI: scanning is finished
UBI: attached mtd1 (name "ubilayer_v5", size 127 MiB) to ubi0
UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
UBI: good PEBs: 1010, bad PEBs: 6, corrupted PEBs: 0
UBI: user volume: 13, internal volumes: 1, max. volumes count: 128
UBI: max/mean erase counter: 36/11, WL threshold: 512, image sequence number: 1520333709
UBI: available PEBs: 2, total reserved PEBs: 1008, PEBs reserved for bad PEB handling: 14
UBI: background thread "ubi_bgt0d" started, PID 315
Warning: unable to open an initial console.
squashfs_cache_init: sqcachesize=8.
VFS: Mounted root (squashfs filesystem) readonly on device 31:6.
Freeing unused kernel memory: 176K (c0436000 - c0462000)
******** Total Boot time: 1038 ms, uncompress initrd cost 0 ms ********
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
1010e000.uart: ttyAMA0 at MMIO 0x1010e000 (irq = 77) is a 16550A
mount file system
Loading the kernel modules:
Loading module: rng-core
Loading module: nf_conntrack
Loading module: xt_mark
Loading module: xt_connmark
Loading module: xt_MARK
modprobe: module xt_MARK not found in modules.dep
Loading module: xt_limit
Loading module: xt_state
Loading module: xt_tcpmss
Loading module: nf_nat
Loading module: ipt_REDIRECT
Loading module: ipt_NETMAP
modprobe: module ipt_NETMAP not found in modules.dep
Loading module: nf_conntrack_ipv4.ko
Loading module: nfnetlink.ko
Loading module: nfnetlink_log.ko
Loading module: nfnetlink_queue.ko
Loading module: xt_HL.ko
Loading module: xt_iprange.ko
Loading module: xt_multiport.ko
Loading module: arp_tables.ko
Loading module: arptable_filter.ko
Loading module: ip_tables.ko
Loading module: iptable_filter.ko
Loading module: iptable_mangle.ko
Loading module: arpt_mangle.ko
Loading module: iptable_raw.ko
Loading module: iptable_nat.ko
Loading module: ipt_ULOG.ko
Loading module: ipt_REJECT.ko
Loading module: ipt_ECN.ko
Loading module: ipt_ah.ko
Loading module: xt_LOG.ko
Setting console log message level:
Setting hostname:
Settingup the sysctl configurations:
Setting up interface lo:
Running local startup scripts.
IAS WAP Ver:V800R019C00SPC033B000
IAS WAP Timestamp:2018/08/01 13:01:09
[ 2.504438] current lastword info:Add=0xe0b01000;max_num=300;Add1=0xe0b01000;Add2=0xe0b06000;Add3=0xe0b0b000;
Set msg reader to 598;
flashtype_v5 is 1
tianyi_cut_128 is 1
flashtype_v5_old is 0
Rootfs time stamp:2018-08-09_10:20:41
net.ipv6.ip6frag_high_thresh = 262144
net.ipv6.ip6frag_low_thresh = 196608
sysctl: error: 'net.netfilter.nf_conntrack_frag6_high_thresh' is an unknown key
sysctl: error: 'net.netfilter.nf_conntrack_frag[ 3.086556] ICMPv6: process `sysctl' is using deprecated sysctl (syscall) net.ipv6.neigh.default.base_reachable_time - use net.ipv6.neigh.default.base_reachable_time_ms instead
6_low_thresh' is an unknown key
net.ipv4.neigh.default.base_reachable_time = 300
net.ipv6.neigh.default.base_reachable_time = 300
xpon_mode:2
User init start......
Loading the HISI SD511X modules:
[ 3.139755]
[ 3.139755]SYSCTL module is installed
[ 3.161648]
[ 3.161648]SPI module is installed
/etc/rc.d/rc.start/1.sdk_init.sh: line 212: md: not found
sh: 5115: unknown operand
[ 3.191597]
[ 3.191597]GPIO module is installed
[ 3.216617]
[ 3.216617]I2C module is installed
[ 3.225727]
[ 3.225727]TIMER23 module is installed
[ 3.263217]
[ 3.263217]SERDES module is intalled
[ 3.272935]
[ 3.272935]HW module is installed
[ 3.282068]
[ 3.282068]UART module is installed
[ 3.291842]
[ 3.291842]DMA module is installed
sh: 5115: unknown operand
[ 3.491322]
[ 3.491322]CHIP module is installed
[ 3.498161] set mac work mode ge...set port mode PMODE_SGMII...set port tx/rx enable...set mac work mode ge...set port mode PMODE_SGMII...set port tx/rx enable...set mac work mode ge...set port mode PMODE_SGMII...set port tx/rx enable...set mac work mode ge...set port mode PMODE_SGMII...set port tx/rx enable...
hi_adp_cnt module is installed
[ 4.133745]
[ 4.133745]BRIDGE module is installed
[ 4.147179] PIE USE 2 cpus
[ 4.160210] @@@ set_dma_ops: name:eth0
[ 4.163982]
[ 4.163982]PIE 10:14:56 module is installed
[ 4.212151]
[ 4.212151]PON_LP module is installed
[ 4.259879]
[ 4.259879]EPON module is installed
sh: 5115: unknown operand
[ 4.319987]
[ 4.319987]L3 module is installed
[ 4.326337]
[ 4.326337]L3 API module is installed!
[ 4.341916]
[ 4.341916]OAM module is installed
insmod: can't insert 'hi_sci.ko': No such file or directory
insmod: can't insert 'hi_mdio.ko': No such file or directory
ifconfig eth0 hw ether 9C:1D:36:74:7B:4C
Loading the EchoLife WAP modules: LDSP
[ 4.417400] COMMON For LDSP Install Successfully...
[ 4.438108] GPIO For LDSP Install Successfully...
[ 4.442945] I2C For LDSP Install Successfully...
[ 4.447632] KEY For LDSP Install Successfully...
[ 4.452340] LED For LDSP Install Successfully...
[ 4.476964] UART For LDSP Install Successfully...
insmod: can't insert '/lib/modules/wap/hw_module_battery.ko': No such file or directory
[ 4.502986] OPTIC For LDSP Install Successfully...
insmod: can't insert '/lib/modules/wap/hw_module_rf.ko': No such file or directory
[ 4.532231] hw_wdt_ext_fiq_process ui_time=300
[ 4.537164] <ldsp>board version is 36
[ 4.541044] <ldsp>pcb version is 0
[ 4.544518] <ldsp>orig board version is 36
[ 4.558054] hw_wdt_ext_fiq_process ui_time=299
[ 4.562621] DEV For LDSP Install Successfully...
[ 4.648781] hn5176 For LDSP install successfully...
[ 4.669164] bob type is already know, don't need insmod M02103 KO!
[ 4.711648] bob type is already know, don't need insmod M02103 KO!
insmod: can't insert '/lib/modules/wap/hw_ker_optic_m02103.ko': Operation not permitted
[ 4.767882]
[ 4.767882] ui_curr_soc_type = 12, ui_curr_soc_sub_type = 0
[ 4.775568] hw_dm_pdt_init_file_names /etc/wap/dm.cfg/pd_relation_5117p.cfg/etc/wap/dm.cfg/topo_relation_5117p.cfg
[ 4.827186] hw_dm_init_data suc
[ 4.837826] hw_dm_pdt_init successfully...
[ 4.921905] : Repetat FT name:BBSP_FT_ROUTE_ISOLATION found!
[ 4.949666] : FT(FT_FIRST_ONLINE_FLAG) should not be Added here,use res file!
[ 4.976407] : FT(FT_SSMP_VIETTEL_8045MODE) should not be Added here,use res file!
[ 4.998937] : FT(FT_PIE_ACK_IGNORE_ERRCODE) should not be Added here,use res file!
[ 5.010447] : FT(FT_TCPFLOW_MONITOR) should not be Added here,use res file!
[ 5.086037] : FT(FT_LOID_AND_APP_URL) should not be Added here,use res file!
[ 5.096953] : FT(FT_CWMP_MONITOR_INFORM_ONCE) should not be Added here,use res file!
[ 5.108887] : FT(HW_AMP_FEATURE_APPM_NOT_START) should not be Added here,use res file!
[ 5.122334] : FT(HW_FEATURE_OSGI) should not be Added here,use res file!
[ 5.140584] : FT(FT_WLAN_DFS_RESTORE) should not be Added here,use res file!
[ 5.151552] : FT(FT_WLAN_SHOW_FIRST_SSID) should not be Added here,use res file!
[ 5.171431] load ft
[ 5.173614] origin path:
=======v_version:V500
V500 load ex rootfs
HW_DM_GetUbootVersion:V500R019C00SPC050B051
HW_DM_GetUbootVersion:1
Step into TOOL_ScanAndMountDyPacketInMtd
HeadInfo:V500R019C00SPC050B051 | SIGNINFO, CheckRet :0
HeadInfo:V500R019C00SPC050B051 | UBOOT, CheckRet :0
HeadInfo:V500R019C00SPC050B051 | KERNEL, CheckRet :0
HeadInfo:V500R019C00SPC050B051, CheckRet :1
Ret:0x0, Get BRootfsformFileName:mtdblock6 Offset 0x221000
CurrentArea: 0, mtd:mtdblock6, RootfsOffset = 0x221000
HeadInfo:V500R019C00SPC050B051 | SIGNINFO, CheckRet :0
HeadInfo:V500R019C00SPC050B051 | UBOOT, CheckRet :0
HeadInfo:V500R019C00SPC050B051 | KERNEL, CheckRet :0
HeadInfo:V500R019C00SPC050B051, CheckRet :1
Ret:0x0, Get BRootfsformFileName:mtdblock6 Offset 0x221000
CurrentArea: 0, mtd:mtdblock6, RootfsOffset = 0x221000
Version:EXROOTFS_HD:WIFI:1151, Type:5
Packet:EXROOTFS_HD:WIFI:1151, CheckRet:1, Rootfs:0x5b6ba4f9, DY:0x5b6ba4f9
mount info:
dyname:EXROOTFS_HD:WIFI:1151,offset:0x112b000,length:0x2a8fac,crc:0xd28eac99,flag:0x0,isinmtd:0x1,src_path:mtdblock6,ram_path:/var/image/wifi_1151,mount_path:/var/dynrootfs/wifi/1151Read mtdblock6 from 0 's 0x112b000 to /var/image/wifi_1151
[ 5.571806] squashfs_cache_init: sqcachesize=8.
Version:EXROOTFS_HD:SLIC:LE964X, Type:5
Packet:EXROOTFS_HD:SLIC:LE964X, CheckRet:1, Rootfs:0x5b6ba4f9, DY:0x5b6ba4f9
mount info:
dyname:EXROOTFS_HD:SLIC:LE964X,offset:0x13d4000,length:0x1bfac,crc:0xf6ef8c64,flag:0x0,isinmtd:0x1,src_path:mtdblock6,ram_path:/var/image/slic_le964x,mount_path:/var/dynrootfs/slic/le964xRead mtdblock6 from 0 's 0x13d4000 to /var/image/slic_le964x
Version:EXROOTFS_SF:PON:GPON:FORCE, Type:6
Packet:EXROOTFS_SF:PON:GPON:FORCE, CheckRet:1, Rootfs:0x5b6ba4f9, DY:0x5b6ba4f9
mount info:
dyname:EXROOTFS_SF:PON:GPON:FORCE,offset:0x13f0000,length:0x91fac,crc:0xe043a2c,flag:0x0,isinmtd:0x1,src_path:mtdblock6,ram_path:/var/image/pon_gpon,mount_path:/var/dynrootfs/pon/gponRead mtdblock6 from 0 '[ 5.664756] squashfs_cache_init: sqcachesize=8.
s 0x13f0000 to /var/image/pon_gpon
Version:EXROOTFS_END:END, Type:9
Step into TOOL_ScanAndMountDyPacketInFile
HeadInfo:V500R019C00SPC050B051 | SIGNINFO, CheckRet :0
HeadInfo:V500R019C00SPC050B051 | UBOOT, CheckRet :0
HeadInfo:V500R019C00SPC050B051 | KERNEL, CheckRet :0
HeadInfo:V500R019C00SPC050B051, CheckRet :1
Ret:0x0, Get BRootfsformFileName:mtdblock6 Offset 0x221000
CurrentArea: 0, mtd:mtdblock6, RootfsOffset = 0x221000
Open Dir /mnt/jffs2/shaopian fail, maybe the dir is not exsit. that's ok~
Step into TOOL_ScanAndMountExRoorfs
HeadInfo:V500R019C00SPC050B051 | SIGNINFO, CheckRet :0
HeadInfo:V500R019C00SPC050B051 | UBOOT, CheckRet :0
HeadInfo:V500R019C00SPC050B051 | KERNEL, CheckRet :0
HeadInfo:V500R019C00SPC050B051, CheckRet :1
Ret:0x0, Get BRootfsformFileName:mtdblock6 Offset 0x221000
CurrentArea: 0, mtd:mtdblock6, RootfsOffset = 0x221000
Packet:EXROOTFS:ROOTFS, CheckRet:1, Rootfs:0x5b6ba4f9, DY:0x5b6ba4f9
Read mtdblock8 from 0 's 0x0 to /var/image/exrootfs
[ 6.499546] squashfs_cache_init: sqcachesize=8.
[ 6.528103] pcie0 sel: 0x1, pcie1 sel:0x2,pcie0 memsize:0xa00000, pcie1 memsize:0xa00000.
[ 6.565379] PCIE0 1.1 Device Link Up val = 0x00808028, loop = 30.
[ 6.572518] PCIE1 1.1 Device Link Up val = 0x00808028, loop = 3.
[ 6.579945] PCI host bridge to bus 0000:00
[ 6.584050] pci_bus 0000:00: root bus resource
[ 6.590946] pci_bus 0000:00: root bus resource
[ 6.597808] pci_bus 0000:00: No busn resource found for root bus, will use
[ 6.605730] pci 0000:00:00.0: type 00 class 0x028000
[ 6.611767] pci 0000:00:00.0: reg 10:
[ 6.617992] pci 0000:00:00.0: supports D1 D2
[ 6.622247] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 6.628486] PCI: bus0: Fast back to back transfers disabled
[ 6.634057] pci_bus 0000:00: busn_res: end is updated to 00
[ 6.641115] PCI host bridge to bus 0000:01
[ 6.645209] pci_bus 0000:01: root bus resource
[ 6.652077] pci_bus 0000:01: root bus resource
[ 6.658975] pci_bus 0000:01: No busn resource found for root bus, will use
[ 6.666911] pci 0000:01:00.0: type 00 class 0x028000
[ 6.672943] pci 0000:01:00.0: reg 10:
[ 6.679167] pci 0000:01:00.0: supports D1 D2
[ 6.683421] pci 0000:01:00.0: PME# supported from D0 D1 D3hot
[ 6.689636] PCI: bus1: Fast back to back transfers disabled
[ 6.695199] pci_bus 0000:01: busn_res: end is updated to 01
[ 6.710419] pci 0000:01:00.0: BAR 0: assigned
[ 6.717205] pci 0000:00:00.0: BAR 0: assigned
[ 6.739842] set_dma_ops: name:0000:00:00.0, vendor_id=6629, device_id=4433
[ 6.746700] set_dma_ops: name:0000:01:00.0, vendor_id=6629, device_id=4433
[ 6.753574] set_dma_ops done, total 2 devices.
[ 6.772459] AMP Module Install Successfully...
[ 6.792240] L2QOS Module Install Successfully...
[ 6.812817] EMAC Module Install Successfully...
[ 6.837503] MPCP For LDSP Install Successfully...
[ 6.877164] kbox: ddrram: verify fs magic fail. It's ok if first time using this device
[ 6.885182] kbox_exception_dump abort for NULL dump_path!
[ 6.890804] kbox:create region panic, size=102400
kbox config(Addr---Size)=0x80880000 0x80000
[ 6.914029] register fiq129 callback
[ 6.917705] addr0, 0xdb9e0000
[ 6.920669] addr1, 0xdb9e2000
[ 6.923628] addr2, 0xdbd6c000
[ 6.926586] addr3, 0xdbd6e000
[ 6.929554] fiq_stack init ok
[ 6.932529] fiq_glue_register_handler, ok
[ 6.936364] fiq source is 1!
[ 6.939438] fiq type is 0!
[ 6.942138] fiq clean source is 0!
[ 6.945529] fiq dead loop is 1!
[ 6.948693] set 129 irq to fiq, Priority is 0.
[ 6.954247] fiq first register succeed!
[ 6.959212] kbox:create region ks_main, size=98304
[ 6.964234] kbox:create region ks_0, size=4096
[ 6.968906] kbox:create region ks_1, size=4096
mount: mounting ns on /sys/fs/cgroup/ns failed: No such file or directory
mount: mounting perf_event on /sys/fs/cgroup/perf_event failed: No such file or directory
lxc cgroup mount done!
pots_num=1
usb_num=1
hw_route=1
l3_ex=1
ipv6=1
Read MemInfo Des: 5036
[ 7.229644] HIGHWAY For LDSP Install Successfully...
[ 7.255188] SPI For LDSP Install Successfully...
[ 7.278790] CODEC For LDSP Install Successfully...
[ 7.342687] LE964x For LDSP install successfully...insmod: can't insert './kernel/fs/fuse/fuse.ko': No such file or directory
[ 7.476296] SCSI subsystem initialized
insmod: can't insert './kernel/drivers/scsi/scsi_wait_scan.ko': No such file or directory
[ 7.553380] usbcore: registered new interface driver usbfs
[ 7.559270] usbcore: registered new interface driver hub
[ 7.564977] usbcore: registered new device driver usb
[ 7.592419] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 7.601191] hiusb_start_hcd sucessful(5117p)!
[ 7.605637] hiusb-ehci hiusb-ehci.0: HIUSB EHCI
[ 7.610214] hiusb-ehci hiusb-ehci.0: new USB bus registered, assigned bus number 1
[ 7.618263] hiusb-ehci hiusb-ehci.0: irq 68, io mem 0x10a40000
[ 7.637212] hiusb-ehci hiusb-ehci.0: USB 0.0 started, EHCI 1.00
[ 7.644136] hub 1-0:1.0: USB hub found
[ 7.647978] hub 1-0:1.0: 1 port detected
[ 7.658588] ehci-pci: EHCI PCI platform driver
[ 7.676023] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 7.683350] hiusb-ohci hiusb-ohci.0: HIUSB OHCI
[ 7.687972] hiusb-ohci hiusb-ohci.0: new USB bus registered, assigned bus number 2
[ 7.695548] hiusb-ohci hiusb-ohci.0: irq 67, io mem 0x10a50000
[ 7.762115] hub 2-0:1.0: USB hub found
[ 7.765900] hub 2-0:1.0: 1 port detected
insmod: can't insert './extra/drivers/usb/host/xhci-hcd.ko': No such file or directory
[ 7.783745] usbcore: registered new interface driver usb-storage
[ 7.797201] usbcore: registered new interface driver usblp
[ 7.823100] usbcore: registered new interface driver cdc_acm
[ 7.828804] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 7.851197] usbcore: registered new interface driver usbserial
[ 7.867830] usbcore: registered new interface driver pl2303
[ 7.873862] usbserial: USB Serial support registered for pl2303
[ 7.885080] usbcore: registered new interface driver cp210x
[ 7.893027] usbserial: USB Serial support registered for cp210x
[ 7.903864] usbcore: registered new interface driver ch341
[ 7.911752] usbserial: USB Serial support registered for ch341-uart
[ 7.929370] usbcore: registered new interface driver ftdi_sio
[ 7.937312] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 7.992477] usbcore: registered new interface driver usbhid
[ 7.998085] usbhid: USB HID core driver
insmod: can't insert './extra/drivers/usb/serial/usbserial.ko': File exists
[ 8.021190] usbcore: registered new interface driver option
[ 8.027325] usbserial: USB Serial support registered for GSM modem (1-port)
[ 8.078755] iconv_init enter
[ 8.100303] USB For LDSP Install Successfully...
insmod: can't insert '/lib/modules/wap/hw_module_datacard.ko': No such file or directory
insmod: can't insert '/lib/modules/wap/hw_module_datacard_chip.ko': No such file or directory
[ 8.127706] usb_init!
insmod: can't insert '/lib/modules/wap/hw_module_tty.ko': No such file or directory
Loading BBSP L2 modules:
[ 8.173120] PPP generic driver version 2.4.2
[ 8.184683] NET: Registered protocol family 24
[ 8.332607]
[ 8.332607]l2ffwd_init old!
[ 8.355605]
[ 8.355605]btv_wifi_init soft_fwd_spec[-1089683004] ret[-148840440]
[ 8.365822]
[ 8.365822]btv_fw_init success!
[ 8.428291] bbsp ptpdrv install ......
Mac_RegMscFunc GetFunc Addresss: bf792000
[ 8.487262] hw_igmp_module_init ui_totalnum:45
[ 8.492142] hw_igmp_kernel Install Successfully...
[ 8.497695] pppoe_module_init load success!
[ 8.502048]
[ 8.502048]vlanflt_module_init g_en_runningMode:0
hw_ringchk_kernel Install Succes[ 8.509088]
[ 8.509088]Have no Res Mac config!
sfully...
hw_portchk_kernel Ins[ 8.516967] l2base For BBSP Install Successfully...
tall Successfully...
mirror workqueueinit ok, Max:1024
[ 8.593187] pdt l3 install start...
[ 8.596807] pdt l3 install successfully...
Loading BBSP L2_extended modules:
[ 8.652307] l2ext For BBSP Install Successfully...
rfc2544 module Install Successfully...
[ 8.680584] pdt QOS install successfully...
qos dscp to pbit installed ok!
Loading BBSP L3_basic modules:
insmod: can't insert '/lib/modules/wap/hw_ssp_gpl_ext.ko': No such file or directory
Load hw_wifi_diagnose_ct.ko
[ 8.787205] 1183 hw_wifi_diagnose_ct_init called
[ 8.792522] 0 curren g_wlannum_ct: 2
Bad file descriptor:265, tid:1099
[ 9.057138] vlanflt_module_init load success !
[ 9.061964] pppoe_cmd_module_init load success !
[ 9.067110] l3base for bbsp Install Successfully...
Loading DSP temporary modules:
[ 9.091249] linux kernel dopra is installed!
[ 9.242672]
[ 9.242672] dsp sdk insmod success! Addr: 0x9c500000 0xe05df000 0x9c0e0000 0xe06e0000.
[ 9.252077] SDK soc type 0
[ 9.262095] DSP For VOICE Install Successfully...
Loading BBSP L3_extended modules:
[ 9.288166] gre: GRE over IPv4 demultiplexor driver
[ 9.297231] ip_gre: GRE over IPv4 tunneling driver
insmod: can't insert '/lib/modules/wap/napt.ko': No such file or directory
[ 9.399092] arp_config_bridge_filter:
[ 9.403200] hw_arp_announce_module_init load success !
[ 9.408556] arp_module_init load success !
[ 9.412738] hw_route_ipv4_module_init in
[ 9.417147] Route ipv4 for bbsp Install Successfully...
[ 9.422763] Neighbour discovery for bbsp Install Successfully...
[ 9.429610] Portal For BBSP Install Successfully...
[ 9.436082] User device for bbsp Install Successfully...
[ 9.441493]
[ 9.441493] ====hw_firewall_log_hook is registered!
[ 9.449603] hw_conntrack_dyn_rsv_ini v1.0!
[ 9.454215] ipfpm_pathdata_init Successfully...
[ 9.460658]
[ 9.463434] l3ext for bbsp Install Successfully...
[ 9.482082] conenat init success
[ 9.579420]
[ 9.579420]hw_ker_capture_useragent_proc_init type succ!
[ 9.586921]
[ 9.586921]hw_ker_capture_add_callback type succ!
[ 9.593785]
[ 9.593785]hw_ker_capture_init_callback succ!
_init_session SUCCESS
table_siz[ 9.600215]
[ 9.600215]hw_ker_capture_useragent_proc_init type succ!
e =1024 hash_size = 128
[ 9.610426]
[ 9.610426]hw_ker_capture_add_callback type succ!
hw_ker_capture_cfg_init load [ 9.619525] Init hw ker capture ko succ .... !success !
Loading BBSP IPv6 modules:
[ 9.671797] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 9.724707] sit: IPv6 over IPv4 tunneling driver
[ 9.754857] hw_route_ipv6_module_init in
[ 9.759926] Route ipv6 for bbsp Install Successfully
Bad file descriptor:202, tid:1179
[ 9.903563]
[ 9.903563] for bbsp Install Successfully...
[ 9.911528] pdt start to install...
[ 9.916348] pdt install successfully...
[ 9.921476] pdt l3 install successfully...
Napt PDT For BBSP Init Successfully...
insmod: can't insert '/lib/modules/wap/ethoam_adpt.ko': No such [ 9.934547] ker_video_diag For BBSP Install Successfully...
file or directory
insmod: can't insert '/lib/modules/wap/btv_adpt.ko': No such file or directory
Loading BBSP l2tp modules:
[ 9.979760] l2tp_core: L2TP core driver, V2.0
[ 9.989245] l2tp_ppp: PPPoL2TP kernel driver, V2.0
Loading netfilter extend connmark modules:
insmod: can't insert '/lib/modules/wap/access_inform.ko': No such file or directory
mac_filter installed ok!
[ 10.102076]
[ 10.102076] type: 0, pool: 0xdb7cff40, cur:512, max:512
[ 10.111878]
[ 10.111878] type: 1, pool: 0xdb7cff80, cur:1536, max:1536
[ 10.122832]
[ 10.122832] type: 2, pool: 0xdb7cffc0, cur:2048, max:2048
[ 10.129912]
[ 10.129912] @@@@@@ skpool_init success @@@@@@
note:skpool installed!
insmod: can't insert '/lib/modules/wap/wds.ko': No such file or directory
wds installed ok!
[ 10.218603]
[ 10.218603] for bbsp Install Successfully...
Start ldsp_user...[ 10.267640] <LDSP> system has slave space for bob
<LDSP_CFG> Set uiUpMode=2
[ 10.292790] SD511X test self OK
[ 10.292790] Optic test self NoCheck
[ 10.292790] WIFI test self OK
[ 10.292790] PHY test self OK
[ 10.292790] PHY test self OK
[ 10.292790] PHY test self OK
[ 10.292790] PHY test self OK
[ 10.292790] PHY test self OK
[ 10.292790] ExtRFtest self NoCheck
[ 10.322381] Create key, key_gpio=31, key_ext=0
[ 10.326824] Create key, key_gpio=255, key_ext=255
[ 10.331510] Create key, key_gpio=255, key_ext=255
[ 10.336204] Create key, key_gpio=255, key_ext=255
[ 10.340890] Create key, key_gpio=255, key_ext=255
[ 10.345577] Create key, key_gpio=255, key_ext=255
[ 10.350269] Create key, key_gpio=255, key_ext=255
[ 10.354956] Create key, key_gpio=255, key_ext=255
[ 10.359649] Create key, key_gpio=0, key_ext=0
[ 10.363989] Create key, key_gpio=0, key_ext=0
[ 10.436173]
[ 10.436173] <LDSP> bob optic was calibrated
[ 10.442081]
[ 10.442081] <LDSP> HN5176 optic . . .
[ 10.491901] <LDSP> HN5176 optic init success!
[ 10.496439] <LDSP> optic para load success!
[ 10.547049]
[ 10.547049]epon .........HI_DP_5118_FPGA:0 mode:2
[ 10.581070]
base addr:0xed100000
base addr:0x00000006
: 0x00000007
[ 10.590716] hs_emac_cbb_reginfo_init success !
hs_emac_func_module_init success !
[ 10.600166] EPON init success !
[ 10.600166]
[ 10.604971]hi_sdk_debug_info_register epon ok!
[ 10.609987]
[ 10.609987]epon_api module is installed
[ 10.755496] kbox:create region deadlock, size=131072
[ 10.777326] wifi drv event modules initssmp bbsp igmp amp comm oam cwmp usb_mngt
-l bbsp cwmp usb_mngt dlna usb_ftp uplinkqos tr098qos ssmp tr143
Start SSMP...
Start COMM...
Start BBSP...Start AMP...Start IGMP...Start WIFI...Start USB_MNGT...
Start pid=1333; uiProcNum=8;
chmod: /var/wan/dns: No such file or directory
taskset: can't execute 'oam': No such file or directory
current soc is 5117P"
ParseOneLine
Failed!
InitFrame igmp; PID=1353; state=0; 9;
InitFrame igmp; PID=1353; in state=0; 9;
InitFrame igmp; PID=1353; out state=0; 9;
InitFrame comm; PID=1335; state=0; 9;
comm: invalid option -- l
HW_Init_ProcArgs: 63
InitFrame comm; PID=1335; in state=0; 9;
InitFrame comm; PID=1335; out state=0; 9;
InitFrame usb_mngt; PID=1343; state=0; 9;
InitFrame usb_mngt; PID=1343; in state=0; 9;
InitFrame usb_mngt; PID=1343; out state=0; 9;
InitFrame amp; PID=1357; state=0; 9;
InitFrame amp; PID=1357; in state=0; 9;
InitFrame amp; PID=1357; out state=0; 9;
/lib/libhw_wifi_cwmp_abroad.so not exist!
/lib/libhw_wifi_cwmp_abroad.so not exist!
InitFrame cwmp; PID=1352; state=0; 10;
InitFrame cwmp; PID=1352; in state=0; 10;
InitFrame cwmp; PID=1352; out state=0; 10;
InitFrame ssmp; PID=1354; state=0; 10;
InitFrame ssmp; PID=1354; in state=0; 10;
InitFrame ssmp; PID=1354; out state=0; 10;
InitFrame wifi; PID=1356; state=0; 10;
Proc Registered DelayInit.
HW_DINIT_WaitStart Begin .
HW_COMM_FrameInit start!
InitFrame bbsp; PID=1336; state=0; 10;
InitFrame bbsp; PID=1336; in state=0; 10;
HW_uplinkqos_AppInit:HW_IP_LOAD_RESOURCE
load uplinkqos ttree
load TR098QoS ttree
tr098qos load view success
InitFrame bbsp; PID=1336; out state=0; 10;
profile close core dump
Press any key to get started
11111111111111111111111111
我的E改G，正常使用哈，你们是不是改错了
markcqm 发表于 2020-10-29 21:24
HS8145V5刷机后E变成了G，改双模无用，再改E，然后变砖了。
TTL走了一大堆，最后提示，无法接收任何指令 ...
请教接线顺序