ZTE zx279127evb 最新型号！！！
Boot NAND
C
U-Boot 2013.04 (Sep 18 2017 - 10:34:17)
CPU: ZX279127@A9,800MHZ
Board: ZTE zx279127evb
DRAM:256 MiB
com1
product_vid = 128
vid=66-F627
NAND:
Manu ID: 0xc8, Chip ID: 0xda (ESMT NAND 256MiB 3,3V 8-bit)
256 MiB
<nand_read_skip_bad_,1276>!mtdpart=0x1,offset=0x0,mtdpartoffset=0x180000,mtdPartsize=0x80000,length=0x20000
In: serial
Out: serial
Err: serial
Net: addr 0x94000008 before value is f9ff1fcf
addr 0x94000008 after value is ffff1fcf
serdes init done
init fe_phy first!
eth0
Hit 1 to upgrade software version
Hit any key to stop autoboot:1 0
do_mcupg function enter..
mac 4 phy status changed: 10M half-duplex
-----smac_init
Using eth0 device
multi upgrade check timeout.
Receive multicast packet failed (>.<)
addr=200000
addr=2200000
select=0x0
search=0x2
<nand_read_skip_bad_,1276>!mtdpart=0x4,offset=0x0,mtdpartoffset=0x4200000,mtdPartsize=0x600000,length=0x1000
BootImageNum=0x00000000,0
select=0x0
search->result.entry=200140
<nand_read_skip_bad_,1276>!mtdpart=0x2,offset=0x0,mtdpartoffset=0x200000,mtdPartsize=0x2000000,length=0x1702bb0
<nand_read_skip_bad_,1276>!mtdpart=0x0,offset=0x0,mtdpartoffset=0x0,mtdPartsize=0x180000,length=0x40000
lseek=0x4403e000
cmdline=U-Boot V1.0.04.167 20170918104636
## Booting kernel from Legacy Image at 42000140 ...
Image Name: Linux Kernel Image
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 24128038 Bytes = 23 MiB
Load Address: 40008000
Entry Point:40008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
----------------------
|-->setup versioninfo tag...
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Booting Linux on physical CPU 0
Linux version 3.4.110 (zxic@zxric-nb) (gcc version 4.7.2 (Buildroot 2015.08.1) ) #110 PREEMPT Mon Sep 18 10:45:44 CST 2017
CPU: ARMv7 Processor revision 1 (ARMv7), cr=18c53c7d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: ZTE ZX279127 (Device Tree), model: ZTE ZX279127
Memory policy: ECC disabled, Data cache writealloc
======= zx_map_io =======
zx279128 clk init ok.
Built 1 zonelists in Zone order, mobility grouping on.Total pages: 65024
Kernel command line: console=ttyS0,115200n8 rdinit=/sbin/init mem=256M; U-Boot V1.0.04.167 20170918104636 0x200000 0x0 0x83 0x82
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB = 256MB total
Memory: 173748k/173748k available, 88396k reserved, 0K highmem
Virtual kernel memory layout:
vector: 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap: 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0xd0800000 - 0xff000000 ( 744 MB)
lowmem: 0xc0000000 - 0xd0000000 ( 256 MB)
modules : 0xbf000000 - 0xc0000000 (16 MB)
.text : 0xc0008000 - 0xc059871c (5698 kB)
.init : 0xc0599000 - 0xc3599000 (49152 kB)
.data : 0xc359a000 - 0xc35d0720 ( 218 kB)
.bss : 0xc35d0744 - 0xc3615678 ( 276 kB)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:256
sched_clock: 31 bits at 25MHz, resolution 40ns, wraps every 85899ms
zxic zx279128 system timer initialized
console enabled
register_console: zx29 console registered!
Calibrating delay loop... 1594.16 BogoMIPS (lpj=7970816)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
Setting up static identity map for 0x40403398 - 0x404033f0
NET: Registered protocol family 16
11930:22:53 [(1056)LogStdioProcInit] LogStdioProcInit
LogUdpWatchProcInit
e8_arp_detect_init OK!
L310 cache controller enabled
l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x32420000, Cache size: 131072 B
product_vid = 66
current_board=c35ac4f0
current vid:66 slicinfo:0x00000002
slic_mode_pinmux_init pinmux_set mod:2 old:0x0003ff97 new:0x00017797
bio: create slab <bio-0> at 0
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource zx_timer0
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP: reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
synopsys pcie probe enter!!!!!!
pcie irq is 71
Add synopsys PCIe port 0
SYNOPSYS pcie port0 memory addr(PA): 0x10000000
SYNOPSYS pcie port0 system control addr(VA): 0xf8500000
SYNOPSYS pcie port0 reg addr(VA): 0xd0808000
SYNOPSYS pcie port0 top crm addr(VA): 0xf8400000
SYNOPSYS pcie port0 phy apb addr(VA): 0xd0810000
SYNOPSYS pcie port0 cfgaddr(VA): 0xd0820000
SYNOPSYS pcie port0 local irq num: 71
SYNOPSYS pcie port0 mem_offset: 0x0
init synopsys pcie
synopsys pcie driver preinit
synopsys pciePreInit Controller 0
synopsys pcie0 controller setting
synopsys pcie0 controller waitting L0 state
pcie0 link up,cnt 12!
synopsys pcie port0 irqs setting
pcie0 irq is 71
synopsys pcie port0 windows map setting
synopsys pcie controller0 enable
**********synopsys PCIe Setup*********
synopsys pcie port0 controller root bus: 0
**********synopsys PCI driver ScanBus************
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource
PCI: bus0: Fast back to back transfers disabled
pci 0000:00:00.0: BAR 0: assigned
tdm registered!
zx_tdm2.0_probe version_20170119
g_tdm_buf =ffdfe000,4aba6000
remap tdm reg 9a107000 to f8807000
tdm irq=54
reg 0xf8800030 value is 0x11b
pon init
ZX_PA_BUF_BASE0=4e900000
ZX_VA_BUF_BASE0=ce900000
ZX_ACL_BASE=4e920000
ZX_FLOW_BASE=4ed20000
ZX_BP_BUFFER_BASE=4eda0000
ZX_DESC_BASE=4fea0000
ZX_TX_UP_DESC_BASE=4ff60000
ZX_TX_DN_DESC_BASE=4ff70000
ZX_VA_BPPE_BASE=ce900000
ZX_VA_BP_BUF_BASE=ceda0000
ZX_VA_DESC_BASE=cfea0000
ZX_VA_TX_UP_DESC_BASE=cff60000
ZX_VA_TX_DN_DESC_BASE=cff70000
UNCACHE_ADDR_OFFSET=22700000
BPPE_POOL_SIZE=1e20
NORMAL_BP_BUFFER_SIZE=1100000
JUMBO_BP_SIZE=0
JUMBO_BPPE_POOL_SIZE=0
BP_BUFFER_SIZE=1100000
BMU_TOTAL_BUFFER_SIZE=1680000
the pon mode is 0
chip_ver: 2
pon clk reset pin mux
pp init
pp net init ok
switch init
idm_desc_init ffdf8000/4dc58000
idm net init ok
mac 1 link down!
mac 2 link down!
mac 3 link down!
NTFS driver 2.1.30 .
jffs2: version 2.2. (NAND) 漏 2001-2006 Red Hat, Inc.
fuse init (API version 7.18)
msgmni has been set to 339
io scheduler noop registered
io scheduler deadline registered (default)
ttyS0 at MMIO 0x0 (irq = 42) is a zx29_UART
ZTE-TSP zx29 UART_0 probe OK
ZTE-TSP zx29 UART driver registered
brd: module loaded
loop: module loaded
Generic platform RAM MTD, (c) 2004 Simtec Electronics
nand_data:d80000,denali_reg:d00000,denali->flash_reg:f8900000,denali->flash_mem:f8980000
ID of nandflash: 0x9590dac8
find:F59L2G81A-25TG
NAND device: Manufacturer ID: 0xc8, Chip ID: 0xda (GigaDevice NAND 256MiB 3,3V 8-bit)
denali->mtd.oobsize:64
8 bit device!
Scanning device for bad blocks
Creating 15 MTD partitions on "denali-nand":
0x000000000000-0x000010000000 : "whole flash"
0x000000000000-0x000000200000 : "u-boot"
0x000004800000-0x000004c00000 : "parameter tags"
0x000000200000-0x000002200000 : "kernel0"
0x000005400000-0x000005800000 : "middleware"
0x000004c00000-0x000005400000 : "usercfg"
0x000002200000-0x000004200000 : "kernel1"
0x000004200000-0x000004800000 : "others"
0x000005800000-0x000005c00000 : "wlan"
0x000005c00000-0x000005e00000 : "phoneapp"
0x000006000000-0x000007e00000 : "osgi"
0x000009c00000-0x00000ff60000 : "plugin_data"
0x000007e00000-0x000009c00000 : "osgi1"
0x000005e00000-0x000006000000 : "phoneapp1"
0x00000ff60000-0x000010000000 : "GN25L95_datas"
zx_spi_probe...master->bus_num:0
zx_spi 9a105000.ssp: master is unqueued, this is deprecated
SPI0 probed
dwc2 9000000.usb: 0 invalid for otg_cap parameter. Check HW configuration.
dwc2 9000000.usb: 1024 invalid for host_nperio_tx_fifo_size. Check HW configuration.
dwc2 9000000.usb: 1024 invalid for max_packet_count. Check HW configuration.
dwc2 9000000.usb: DWC OTG Controller
dwc2 9000000.usb: new USB bus registered, assigned bus number 1
dwc2 9000000.usb: irq 66, io mem 0x00000000
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: DWC OTG Controller
usb usb1: Manufacturer: Linux 3.4.110 dwc2_hsotg
usb usb1: SerialNumber: 9000000.usb
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
zx29_hsotg: version 3.10b 20-MAY-2013
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
usbcore: registered new interface driver usbserial_generic
USB Serial support registered for generic
usbserial: USB Serial Driver core
usbcore: registered new interface driver cp210x
USB Serial support registered for cp210x
usbcore: registered new interface driver pl2303
USB Serial support registered for pl2303
i2c /dev entries driver
i2c_register_board_info i2c_device0
I2C probe successed!
<pdt_wdt_init>(526):creat proc files for watchdog!!!
<pdt_wdt_init>(530):Starting Watchdog Timer...
wdt debug: nr_cpu_ids= 1
zxwdt: heartbeat 2 msec, clock 800000000
cpuidle: using governor ladder
nf_conntrack version 0.5.0 (2714 buckets, 8128 max)
MAXNET DPI interface Loaded
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
Bridge firewalling registered
Ebtables v2.0 registered
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
PPP generic driver version 2.4.2
NET: Registered protocol family 24
systools version:v0.7.5
zte--oss cpu usage module init
iprt_data_init success!
mirror_kthread start success!
detail process rule start
e8_init OK!
FLowRL module init
DevBwFreeing init memory: 49152K
init started:BusyBox v1.01 (2017.09.12-08:38+0000) multi-call binary
Starting pid 547, console /dev/ttyS0: '/etc/init.d/rcS'
mounting /dev/mtdblock2 to /tagparam, wait ...
Mounting ramdisk at /var and /usr/cpkTmp
Mounting /dev/mtdblock5 to /userconfig
Mount ok!
<3000000008>11930:22:58 [(1352)CheckLogConfFile] CheckLogConfFile%CheckRestartCntConfFile
<3000000008>
jffs2: Empty flash at 0x0265ea2c ends at 0x0265f000
jffs2: Empty flash at 0x037ed0d4 ends at 0x037ed800
jffs2: Empty flash at 0x04eb1258 ends at 0x04eb1800
[: missing ]
--------------- ptarget is 0 ---------------
************************** mout mtdblock9 *********************
Mounting /dev/mtdblock14 to /GN25L95_datas
Mount ok!
mounting /dev/mtdblock8 to /wlan, wait ...
Configuring MAC interfaces
ls: /etc/sysconfig/network-scripts/ifcfg-mii*: No such file or directory
Bringing up interface lo
lo up
Using /kmodule/bspdriver.ko
storage_wakeup_proc_create success!
<verinfo_module_init>(1005)---->verinfo=U-Boot V1.0.04.167 20170918104636 0x200000 0x0 0x83 0x82
addr==200000
<verinfo_module_init>(1010)---->s32Description is ZXIC GM219-S UNI V1.0.04.167
s8VendorInfo is ZXIC
flag is 0
<verinfo_module_init>(1012)----><verinfo_module_init>(1014)---->fail_addr=40,i2c_probe(0x50) failed.
GN25L95 found.
bspdriver select GN25L95 mode is MCU.
=== verify slic info ===
found a port:0 cs:1 ch:0
Siliconlab chip Si3218x found! id:0xaa
cann't Find a port:1
cann't Find a port:2
cann't Find a port:3
Using /kmodule/zx_ponregregister fpga driver success, major=222
.ko
Using /kmodule/tm.ko
= TM Module SYS FS Init ended successfully =
tm_initModule begin...
tm_pp_initial start
input: base=0x4e300000
upa_set_rr_mask_cfg input: upa_rr_mask = 0x2ab
tm_pp_initial--------finish
tm_switch_initial----start
tm_switch_initial----finish
tm_initial successed !!!
enter tm_sdk_init
exit tm_db_init
tm_initModule end...
pon up
omci up
Using /kmodule/netdriver.ko
ethdriver_init....
g_mii_dev_namesw
g_mii_dev_namepon
sw up
Using /kmodule/zte_gpon.ko
zteGpmac_initModule begin...
=== GponMac Supported MaxTcont: 16 MaxPLI: 800B ===
##huoqf zteGponAsicStarttimeChkResultInit write cfg=10
##huoqf zteGponAsicStarttimeChkResultInit read cfg=10
= PON Module Operate ended successfully =
state o1 =>o2
state o2 =>o1
DEbug: GPON PIN_MUX_REG3:(0x20d00420)
create zteGpon_rei_task ok!
= GMAC Module SYS FS Init ended successfully =
zteGpmac_initModule end...
Using /kmodule/gpondrv.ko
zx279100_gpon_Init ok
Using /kmodule/switch.ko
Init switch module
zy switch detected boardtype:192
zy uni num:4
switch config 9127/9128 GPONmode!
reg hff
set cpu queue rate limit to 4000pps
reg get statistics
Init switch module Success
Using /kmodule/optical.ko
fail_addr=40,i2c_probe(0x50) failed.
bsp_i2c_probe 0x50 failed!
GN25L95 found.
bsp_GN25L95_probe 0x51 success!
Optical select GN25L95 mode is MCU.
vendor name = ZTE_B+_G
optical PN(0x60) =
optical PN(0x28) = GN25L95
Using /kmodule/kudp.ko
udpwatchd inited!
kudpinited!
Using /kmodule/voip_codec.ko
Init codec v1.0(For ZXHN_ROSTELECOM_F680V2.0)!
Using /kmodule/dsp_dev.ko
----VoIPCodecInit ch0
----VoIPCodecInit ch1
P_2833: Setup 0
DSP device setup OK!
idm0 up
insmod: /lib/modules/3.4.110: No such file or director
"Result": 0,
"Vendor": "CIOT",
"ProductCLass": "GM219-S",
"HardwareVer": "HV1.0.04.167",
"FirmwareVer": "V1.0.04.167",
"FlashSize": 256,
"RamSize": 256,
"MainChipClass": "ZX279127",
"NFC": "0"
}
#NativePostPacket jsonObject = {"ssidIndex":1,"CmdType":"GET_WLANSSIDINFO"}
in wlan_mm_main wState = 1, dwmsgid = 0x22402, wEvent = 0x2402
#NativePostPacket strReturn = {
"Result": 0,
"Enable": "TRUE",
"BSSID": "64:f8:8a:09:71:76",
"SSIDName": "CMCC-CWcy",
"SSIDAdvertisementEnabled": "TRUE",
"Standard": "11bgn",
"EncryptionMode": "MIXED-WPAPSK2"
}
#NativePostPacket jsonObject = {"CmdType":"GET_DEVICEUPTIME"}
#NativePostPacket strReturn = 81
#NativePostPacket jsonObject = {"CmdType":"GET_CPUOCCUPANCYRATE"}
#NativePostPacket strReturn = 2
#NativePostPacket jsonObject = {"CmdType":"GET_RAMOCCUPANCYRATE"}
#NativePostPacket strReturn = 16
#NativePostPacket jsonObject = {"CmdType":"GET_INTERNETWANINDEX"}
#NativePostPacket strReturn = 1
#NativePostPacket jsonObject = {"wanIndex":1,"CmdType":"GET_WANIFSTATUS"}
#NativePostPacket strReturn = {
"Result": 0,
"Uptime": "0",
"ConnectionStatus": "Disconnected",
"IPv6ConnStatus": "Unconfigured",
"LastConnectionError": "ERROR_NONE"
}
#NativePostPacket jsonObject = {"hostClass":"ONLINE","CmdType":"GET_LANHOSTINFOBYCLASS"}
#NativePostPacket strReturn = {
"Result": 0,
"List": []
A9的U,性能咋样?
页:
[1]