【求助】各位看看hg8245c2的tll信息，怎么中断，和刷入呀。
各位帮看一下，hg845c2刷英文版，回不去了，载入完后，也无法像原固件那样可以用命令了，特来求助，谢谢。
===================================================
HuaWei StartCode 2012.02 (R13C10 Apr 22 2014 - 18:06:02)
NAND:Nand(Hardware): 128 MiB
startcode select the uboot to load
the high RAM is :8080103c
startcode uboot boot count:142934274
use the main slave_param area from flash, the RAM data is not OK!!!
Use the UbootB to load first
Use the UbootB to load success
U-Boot 2010.03 (R13C10 Aug 29 2014 - 19:47:02)
DRAM:128 MB
Boot From NAND flash
Chip Type is SD5115T
NAND:Special Nand id table Version 1.23
Nand ID: 0x2C 0xF1 0x80 0x95 0x04 0x00 0x00 0x00
NAND FLASH Enter Low Driver Mode
Nand(Hardware): Block:128KB Page:2KB Chip:128MB*1 OOB:64B ECC:4Bytes
128 MiB
Using default environment
In: serial
Out: serial
Err: serial
PHY power down !!!
::CRC:0x6a8fe445, Magic1:0x5a5a5a5a, Magic2:0xa5a5a5a5, count:0, CommitedArea:0x1, Active:0x1, RunFlag:0x0
Start from main system(0x1)!
CRC:0x6a8fe445, Magic1:0x5a5a5a5a, Magic2:0xa5a5a5a5, count:1, CommitedArea:0x1, Active:0x1, RunFlag:0x0
0x000000020000-0x000008000000 : "mtd=1"
UBI: attaching mtd1 to ubi0
Main area (B) is OK!
CRC:0xc4e775d4, Magic1:0x5a5a5a5a, Magic2:0xa5a5a5a5, count:1, CommitedArea:0x1, Active:0x1, RunFlag:0x0
Bootcmd:ubi read 0x85c00000 kernelB 0x1ee7a4; bootm 0x85c00054
BootArgs:noalign mem=114M console=ttyAMA1,115200 ubi.mtd=1 root=/dev/mtdblock12 rootfstype=squashfs mtdparts=hinand:0x100000(startcode),0x7f00000(ubifs),-(reserved) pcie0_sel=x1 maxcpus=0 user_debug=0x1f panic=1
U-boot Start from NORMAL Mode!
## Booting kernel from Legacy Image at 85c00054 ...
Image Name: Linux-2.6.34.10_sd5115v100_wr4.3
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2025232 Bytes =1.9 MB
Load Address: 81000000
Entry Point:81000000
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Kernel Early-Debug on Level 0
V: 0xF1100000 P: 0x00010100 S: 0x00001000 T: 0
V: 0xF110E000 P: 0x0001010E S: 0x00001000 T: 0
V: 0xF110F000 P: 0x0001010F S: 0x00001000 T: 0
V: 0xF1104000 P: 0x00010104 S: 0x00001000 T: 0
V: 0xF1180000 P: 0x00010180 S: 0x00002000 T: 0
V: 0xF1400000 P: 0x00010400 S: 0x00001000 T: 12
early_init 72
sd5115_map_io 223
smp_init_cpus 163
sd5115_gic_init_irq 88
sd5115_timer_init 471
sd5115_clocksource_init 451
twd_base :
0xF1180600
sd5115_timer_init 491
smp_prepare_cpus 174
hi_kernel_wdt_init 207
sd5115_init 314
sd5115_init 320
sd5115_init 320
sd5115_init 327
sd5115_init 330
Linux version 2.6.34.10_sd5115v100_wr4.3 (root@vL10t193037) (gcc version 4.4.6 (GCC) ) #1 SMP Fri Aug 29 19:50:53 CST 2014
CPU: ARMv7 Processor revision 1 (ARMv7), cr=10c53c7f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: sd5115
Memory policy: ECC disabled, Data cache writealloc
sd5115 apb bus clk is 100000000
PERCPU: Embedded 7 pages/cpu @c04d9000 s4448 r8192 d16032 u65536
pcpu-alloc: s4448 r8192 d16032 u65536 alloc=16*4096
pcpu-alloc: 0 1
Built 1 zonelists in Zone order, mobility grouping on.Total pages: 28956
Kernel command line: noalign mem=114M console=ttyAMA1,115200 ubi.mtd=1 root=/dev/mtdblock12 rootfstype=squashfs mtdparts=hinand:0x100000(startcode),0x7f00000(ubifs),-(reserved) pcie0_sel=x1 maxcpus=0 user_debug=0x1f panic=1
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 114MB = 114MB total
Memory: 111636k/111636k available, 5100k reserved, 0K highmem
Virtual kernel memory layout:
vector: 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap: 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
vmalloc : 0xc7800000 - 0xd0000000 ( 136 MB)
lowmem: 0xc0000000 - 0xc7200000 ( 114 MB)
modules : 0xbf000000 - 0xc0000000 (16 MB)
.init : 0xc0008000 - 0xc002b000 ( 140 kB)
.text : 0xc002b000 - 0xc0396000 (3500 kB)
.data : 0xc03aa000 - 0xc03c6640 ( 114 kB)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Hierarchical RCU implementation.
RCU-based detection of stalled CPUs is enabled.
NR_IRQS:160
Calibrating delay loop... 1294.33 BogoMIPS (lpj=6471680)
Security Framework initialized
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
Init trace_clock_cyc2ns: precalc_mult = 312500, precalc_shift = 8
Brought up 1 CPUs
SMP: Total of 1 processors activated (1294.33 BogoMIPS).
hi_wdt: User-Mode!
hi_wdt: Init sucessfull!
NET: Registered protocol family 16
id:0x51152100
ACP ON!
ACP bus = 200M!
L2cache cache controller enabled
check_res_of_trace_clock: sched_clock() high resolution
Serial: dwuart driver
uart:0: ttyAMA0 at MMIO 0x1010e000 (irq = 77) is a AMBA/DW
uart:1: ttyAMA1 at MMIO 0x1010f000 (irq = 78) is a AMBA/DW
console enabled
pcie0 sel: 0x1, pcie1 sel:0x0,pcie0 memsize:0xa00000, pcie1 memsize:0xa00000.
PCIE0 Device Link Up val = 0x00008038, loop = 2.
PCI: bus0: Fast back to back transfers disabled
pci 0000:00:00.0: BAR 0: assigned
pci 0000:00:00.0: BAR 0: set to (PCI address
bio: create slab <bio-0> at 0
vgaarb: loaded
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource timer1
NET: Registered protocol family 2
IP route cache hash table entries: 128 (order: -3, 512 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 128 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
squashfs: version 4.0 (2009/01/31) Phillip Lougher
JFFS2 version 2.2. © 2001-2006 Red Hat, Inc.
msgmni has been set to 218
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
brd: module loaded
mtdoops: mtd device (mtddev=name/number) must be supplied
Spi id table Version 1.22
Spi Flash Controller V300 Device Driver, Version 1.10
Special nand id table Version 1.33
Hisilicon Nand Flash Controller V301 Device Driver, Version 1.10
Nand ID: 0x2C 0xF1 0x80 0x95 0x04 0x00 0x00 0x00
Nand(Hardware): Block:128KB Page:2KB Chip:128MB OOB:64B ECC:4Bytes
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xf1 (Micron MT29F1G08ABAEA)
NAND_ECC_NONE selected by board driver. This is not recommended !!
3 cmdlinepart partitions found on MTD device hinand
Creating 3 MTD partitions on "hinand":
0x000000000000-0x000000100000 : "startcode"
0x000000100000-0x000008000000 : "ubifs"
0x000008000000-0x000008000000 : "reserved"
mtd: partition "reserved" is out of reach -- disabled
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
UBI: attached mtd1 to ubi0
UBI: MTD device name: "ubifs"
UBI: MTD device size: 127 MiB
UBI: number of good PEBs: 1016
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 512
UBI: number of internal volumes: 1
UBI: number of user volumes: 14
UBI: available PEBs: 288
UBI: total number of reserved PEBs: 728
UBI: number of PEBs reserved for bad PEB handling: 20
UBI: max/mean erase counter: 6/4
UBI: image sequence number: 1866474915
UBI: background thread "ubi_bgt0d" started, PID 36
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
CSLIP: code copyright 1989 Regents of the University of California.
SLIP linefill/keepalive option.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
hiusb_start_hcd sucessful!
hiusb-ehci hiusb-ehci.0: HIUSB EHCI
hiusb-ehci hiusb-ehci.0: new USB bus registered, assigned bus number 1
hiusb-ehci hiusb-ehci.0: irq 71, io mem 0x10a40000
hiusb-ehci hiusb-ehci.0: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
hiusb-ohci hiusb-ohci.0: HIUSB OHCI
hiusb-ohci hiusb-ohci.0: new USB bus registered, assigned bus number 2
hiusb-ohci hiusb-ohci.0: irq 70, io mem 0x10a50000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
Netfilter messages via NETLINK v0.30.
ip_tables: (C) 2000-2006 Netfilter Core Team
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 17
VFS: Mounted root (squashfs filesystem) readonly on device 31:12.
Freeing init memory: 140K
-=#DOPRA LINUX 1.0#=-
-=#EchoLife WAP 0.1#=-
-=#Huawei Technologies Co., Ltd #=-
mount file system
Loading the kernel modules:
Loading module: rng-core
Loading module: nf_conntrack
nf_conntrack version 0.5.0 (4000 buckets, 16000 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
Loading module: xt_mark
Loading module: xt_connmark
Loading module: xt_MARK
Loading module: xt_limit
Loading module: xt_state
Loading module: xt_tcpmss
Loading module: nf_nat
Loading module: ipt_MASQUERADE
Loading module: ipt_REDIRECT
Loading module: ipt_NETMAP
Loading module: nf_conntrack_ipv4.ko
Loading module: iptable_nat.ko
Making device instances:
Setting console log message level:
Setting hostname:
Settingup the sysctl configurations:
Setting up interface lo:
Running local startup scripts.
*******************************************
--== Welcome To IAS WAP ==--
--== Huawei Technologies Co., Ltd. ==--
*******************************************
IAS WAP Ver:V800R013C10SPC167B001
IAS WAP Timestamp:2014/08/29 17:19:25
*******************************************
Start init IAS WAP basic module ....
current lastword info:Add=0xc7b01000;max_num=300;Add1=0xc7b01000;Add2=0xc7b06000;Add3=0xc7b0b000;
Log hem magic invalid!
Init IAS WAP basic module done!
soft lockup args:snap=150; release=50; dump flag=1;
UBIFS error (pid 103): mount_ubifs: fenghe.linux4.3 : space_fixup = 0
Set kmsgread process pid to:93;
Rootfs time stamp:2014-08-29_20:01:07
SVN label(ont):User init start......
Loading the SD5115V100 modules:
SYSCTL module is installed
PIE module is installed
GPIO module is installed
SPI module is installed
I2C module is installed
DP module is installed
MDIO module is installed
TIMER module is installed
UART module is installed
HW module is installed
ifconfig eth0 hw ether 88:CF:98:7E:9C:40
Loading the EchoLife WAP modules: LDSP
COMMON For LDSP Install Successfully...
GPIO For LDSP Install Successfully...
HIGHWAY For LDSP Install Successfully...
------ SOC is 5115 T PILOT ------
<ldsp>board version is 4061
<ldsp>pcb version is 4
<ldsp>orig board version is 6
CHIPADP-SD5115 BASIC For LDSP Install Successfully...
CHIPADP-SD5115 EXT For LDSP Install Successfully...
I2C For LDSP Install Successfully...
LSW L2 For LDSP Install Successfully...
LSW L3 For LDSP Install Successfully...
DEV For LDSP Install Successfully...
:ae_chip=6,ae_chip=255,ae_chip=255,ae_chip=0
:board_ver=4061,pcb_ver=4
hw_dm_init_data successfully...
[ /mnt/jffs2/boardinfocustom.cfg not exsit ! not need deal.]
hw_dm_pdt_init successfully...
hw_feature_init begin...
hw_feature_proc_init begin...
hw_feature_data_init begin...
ac_cfgpath is not null,acTmpBuf=/etc/wap/customize/common_ft.cfg.....!
ac_hard_cfgpath is not null, acTmpBuf=/mnt/jffs2/hw_hardinfo_feature.bak.....!
ac_cfgpath is not null,acTmpBuf=/etc/wap/customize/spec_common.cfg.....!
ac_hard_cfgpath is not null, acTmpBuf=/mnt/jffs2/hw_hardinfo_spec.bak.....!
hw_feature_init Successfully...
pots_num=2
usb_num=1
hw_route=1
l3_ex=1
ipv6=1
Read MemInfo Des: 1117
SPI For LDSP Install Successfully...
UART For LDSP Install Successfully...
BATTERY For LDSP Install Successfully...
OPTIC For LDSP Install Successfully...
PLOAM For LDSP Install Successfully...
GMAC For LDSP Install Successfully...
KEY For LDSP Install Successfully...
LED For LDSP Install Successfully...
RF For LDSP Install Successfully...
CODEC For LDSP Install Successfully...
PEF3201 For LDSP install successfully...
fuse init (API version 7.13)
SCSI subsystem initialized
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usblp
USB For LDSP Install Successfully...
hw_ker_pdt_usb_init successfully...
Loading BBSP L2 modules:
PTP For BBSP Install Successfully...
hw_igmp_kernel Install Successfully...
dhcp_module_init load success !
pppoe_module_init load success !
hw_ringchk_kernel Install Successfully...
hw_portchk_kernel Install Successfully...
l2base For BBSP Install Successfully...
vbr_unicast_car:50
vbr_unicast_car:50
vbr_unicast_car:50
Pktdump init Install Successfully...
hw_cpu_usage_install
for bbsp Install Successfully...
EMAC For LDSP Install Successfully...
MPCP For LDSP Install Successfully...
Loading DSP temporary modules:
linux kernel dopra is installed!
dsp sdkinsmod success!
DSP For LDSP Install Successfully...
Loading BBSP L2_extended modules:
hw_ethoam_kernel Install Successfully...
l2ext For BBSP Install Successfully...
Loading BBSP L3_basic modules:
Dosflt For BBSP Install Successfully...
vlanflt_module_init load success !
l3base for bbsp Install Successfully...
Loading BBSP L3_extended modules:
arp_config_bridge_filter:
arp_module_init load success !
Route ipv4 for bbsp Install Successfully...
Neighbour discovery for bbsp Install Successfully...
Portal For BBSP Install Successfully...
hw_nat_skip_port_init success
Parent ctrl for bbsp Install Successfully...
User device for bbsp Install Successfully...
l3ext for bbsp Install Successfully...
install success
Loading BBSP IPv6 modules:
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip6tnl0: Disabled Privacy Extensions
Route ipv6 for bbsp Install Successfully
Loading BBSP hw_rout modules:
insmod: can't insert '/lib/modules/wap/l3ext.ko': File exists
insmod: can't insert '/lib/modules/wap/wap_ipv6.ko': File exists
for bbsp Install Successfully...
NAPT_PDT For BBSP Install Successfully...
tunnel process module is installed chip_id = 6
for bbsp Install Successfully...
Start ldsp_user...<LDSP> system has slave space for bob
<LDSP_CFG> Set uiUpMode=1
LINE = 245, FUNC = hi_kernel_i2c_read_byte
read data is over time
SD511X test self OK
Extern Lsw test self NoCheck
Optic test self ERROR
WIFI test self OK
PHY test self OK
PHY test self OK
PHY test self OK
PHY test self OK
PHY test self NoCheck
PHY test self NoCheck
<LDSP> 5171 optic
FILE = /usr1/code/ONT_V3R13C10_DailyCompile/code/current/ONT_V300R013C00/CI/Make/../../Source/ldsp/driver/optic/hw_ker_drv_optic.c
LINE =5864, FUNC = hw_drv_optic_cal_sw_ver_set
<LDSP> read cal version file error
<LDSP> bob optic was calibrated
<LDSP> optic firmware load success!
GPON init success !
ssmp bbsp igmp amp ethoam oamomci voice wifi cwmp
Start SSMP...
Start VOICE ...Start WIFI...current soc is 5115T
Start start pid=385; uiProcNum=9;
InitFrame omci; PID=397; state=0; 13.378;
InitFrame omci; PID=397; in state=0; 13.378;
InitFrame omci; PID=397; out state=0; 13.378;
InitFrame ssmp; PID=386; state=0; 13.892;
InitFrame ssmp; PID=386; in state=0; 13.893;
ubi_open_volume error with 2, try UBI_READONLY;
<db/hw_xml_dbmain.c:7713>acChooseWord:NOCHOOSE UserChoiceFlag:-1 Updateflag:-1
InitFrame igmp; PID=389; state=0; 15.804;
InitFrame igmp; PID=389; in state=0; 15.804;
InitFrame igmp; PID=389; out state=0; 16.130;
InitFrame wifi; PID=398; state=0; 16.265;
InitFrame wifi; PID=398; in state=0; 16.265;
InitFrame wifi; PID=398; out state=0; 16.266;
InitFrame amp; PID=388; state=0; 16.300;
InitFrame amp; PID=388; in state=0; 16.300;
InitFrame amp; PID=388; out state=0; 16.301;
InitFrame cwmp; PID=396; state=0; 16.340;
InitFrame cwmp; PID=396; in state=0; 16.340;
InitFrame cwmp; PID=396; out state=0; 16.340;
InitFrame voice_h248sip; PID=395; state=0; 16.429;
InitFrame voice_h248sip; PID=395; in state=0; 16.430;
InitFrame voice_h248sip; PID=395; out state=0; 16.430;
InitFrame bbsp; PID=387; state=0; 16.517;
InitFrame bbsp; PID=387; in state=0; 16.517;
InitFrame bbsp; PID=387; out state=0; 16.539;
InitFrame ethoam; PID=390; state=0; 16.751;
InitFrame ethoam; PID=390; in state=0; 16.752;
InitFrame ethoam; PID=390; out state=0; 16.752;
<db/hw_xml_dbmain.c:8784>acFilePath:/etc/wap/hw_aes_tree.xml pstRoot:0x0
<db/hw_xml_dbmain.c:9068>acFilePath:/etc/wap/hw_aes_tree.xml pstRoot:0x38342a04
pfFuncHandle ERR. uiRet:ffffffff;
pfFuncHandle ERR. uiRet:ffffffff;
pfFuncHandle ERR. uiRet:ffffffff;
pfFuncHandle ERR. uiRet:ffffffff;
pfFuncHandle ERR. uiRet:ffffffff;
pfFuncHandle ERR. uiRet:ffffffff;
pfFuncHandle ERR. uiRet:ffffffff;
pfFuncHandle ERR. uiRet:ffffffff;
pfFuncHandle ERR. uiRet:ffffffff;
pfFuncHandle ERR. uiRet:ffffffff;
pfFuncHandle ERR. uiRet:ffffffff;
<db/hw_xml_dbmain.c:7100> Set DB Auto Save in 12000 ticks.
============================================================
忘了在哪儿看到的了，中断启动进cfe的ttl设置不一样,好像是115200,8N1,无流控，加电3秒内按esc还是ctrl+c记不得了 zrlw 发表于 2016-2-27 10:21
忘了在哪儿看到的了，中断启动进cfe的ttl设置不一样,好像是115200,8N1,无流控，加电3秒内按esc还是ctrl+c记 ...
都试了，就是不好用呀 看来很多人都一直在关注怎么中断HiBoot (华为海思修改过的U-Boot)进入刷写模式，不过一直也没有看到好的方法。自己改错配置的一个8245H *（256M原版光猫）也吃灰了很久，有空真的要研究下怎么恢复。 宽带技术网宽带技术网宽带技术网宽带技术网
页:
[1]