求助高手hg8245c2改错配置无限重启
HuaWei StartCode 2012.02 (R13C10 Apr 22 2014 - 18:06:02)NAND:Nand(Hardware): 128 MiB
startcode select the uboot to load
the high RAM is :8080103c
startcode uboot boot count:0
use the main slave_param area from flash, the RAM data is not OK!!!
Use the UbootA to load first
Use the UbootA to load success
U-Boot 2010.03 (R13C10 Dec 28 2013 - 14:45:50)
DRAM:128 MB
Boot From NAND flash
Chip Type is SD5115T
NAND:Special Nand id table Version 1.23
Nand ID: 0x01 0xF1 0x00 0x1D 0x01 0xF1 0x00 0x1D
Nand(Hardware): Block:128KB Page:2KB Chip:128MB*1 OOB:64B ECC:4Bytes
128 MiB
Using default environment
In: serial
Out: serial
Err: serial
PHY power down !!!
::CRC:0xa3c1ca20, Magic1:0x0, Magic2:0x0, count:0, CommitedArea:0x0, Active:0x0, RunFlag:0x0
0x000000020000-0x000008000000 : "mtd=1"
UBI: attaching mtd1 to ubi0
slave_paramA in flash, CRC:0xa3c1ca20, Magic1:0x0, Magic2:0x0, count:0, CommitedArea:0x0, Active:0x0, RunFlag:0x0
MAGIC1: 0x0, MAGIC2: 0x0, the magic is error!!!
slave_paramB in flash, CRC:0xa3c1ca20, Magic1:0x0, Magic2:0x0, count:0, CommitedArea:0x0, Active:0x0, RunFlag:0x0
MAGIC1: 0x0, MAGIC2: 0x0, the magic is error!!!
Slave struct initializtion success!!
Start from main system(0x0)!
CRC:0xa3c1ca20, Magic1:0x5a5a5a5a, Magic2:0xa5a5a5a5, count:0, CommitedArea:0x0, Active:0x0, RunFlag:0xffffffff
Main area (A) is OK!
CRC:0xe33b8857, Magic1:0x5a5a5a5a, Magic2:0xa5a5a5a5, count:0, CommitedArea:0x0, Active:0x0, RunFlag:0xffffffff
Bootcmd:ubi read 0x85c00000 kernelA 0x1ee1ac; bootm 0x85c00054
BootArgs:noalign mem=114M console=ttyAMA1,115200 ubi.mtd=1 root=/dev/mtdblock11 rootfstype=squashfs mtdparts=hinand:0x100000(startcode)ro,0x7f00000(ubifs),-(reserved) pcie0_sel=x1 maxcpus=0 user_debug=0x1f panic=1
U-boot Start from NORMAL Mode!
## Booting kernel from Legacy Image at 85c00054 ...
Image Name: Linux-2.6.34.10_sd5115v100_wr4.3
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2023704 Bytes =1.9 MB
Load Address: 81000000
Entry Point:81000000
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Kernel Early-Debug on Level 0
V: 0xF1100000 P: 0x00010100 S: 0x00001000 T: 0
V: 0xF110E000 P: 0x0001010E S: 0x00001000 T: 0
V: 0xF110F000 P: 0x0001010F S: 0x00001000 T: 0
V: 0xF1104000 P: 0x00010104 S: 0x00001000 T: 0
V: 0xF1180000 P: 0x00010180 S: 0x00002000 T: 0
V: 0xF1400000 P: 0x00010400 S: 0x00001000 T: 12
early_init 72
sd5115_map_io 223
smp_init_cpus 163
sd5115_gic_init_irq 88
sd5115_timer_init 471
sd5115_clocksource_init 451
twd_base :
0xF1180600
sd5115_timer_init 491
smp_prepare_cpus 174
hi_kernel_wdt_init 207
sd5115_init 314
sd5115_init 320
sd5115_init 320
sd5115_init 327
sd5115_init 330
Linux version 2.6.34.10_sd5115v100_wr4.3 (root@vL10t185054) (gcc version 4.4.6 (GCC) ) #1 SMP Sat Dec 28 14:50:06 CST 2013
CPU: ARMv7 Processor revision 1 (ARMv7), cr=10c53c7f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: sd5115
Memory policy: ECC disabled, Data cache writealloc
sd5115 apb bus clk is 100000000
PERCPU: Embedded 7 pages/cpu @c04d9000 s4448 r8192 d16032 u65536
pcpu-alloc: s4448 r8192 d16032 u65536 alloc=16*4096
pcpu-alloc: 0 1
Built 1 zonelists in Zone order, mobility grouping on.Total pages: 28956
Kernel command line: noalign mem=114M console=ttyAMA1,115200 ubi.mtd=1 root=/dev/mtdblock11 rootfstype=squashfs mtdparts=hinand:0x100000(startcode)ro,0x7f00000(ubifs),-(reserved) pcie0_sel=x1 maxcpus=0 user_debug=0x1f panic=1
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 114MB = 114MB total
Memory: 111636k/111636k available, 5100k reserved, 0K highmem
Virtual kernel memory layout:
vector: 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap: 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
vmalloc : 0xc7800000 - 0xd0000000 ( 136 MB)
lowmem: 0xc0000000 - 0xc7200000 ( 114 MB)
modules : 0xbf000000 - 0xc0000000 (16 MB)
.init : 0xc0008000 - 0xc002b000 ( 140 kB)
.text : 0xc002b000 - 0xc0395000 (3496 kB)
.data : 0xc03aa000 - 0xc03c65c0 ( 114 kB)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Hierarchical RCU implementation.
RCU-based detection of stalled CPUs is enabled.
NR_IRQS:160
Calibrating delay loop... 1294.33 BogoMIPS (lpj=6471680)
Security Framework initialized
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
Init trace_clock_cyc2ns: precalc_mult = 312500, precalc_shift = 8
Brought up 1 CPUs
SMP: Total of 1 processors activated (1294.33 BogoMIPS).
hi_wdt: User-Mode!
hi_wdt: Init sucessfull!
NET: Registered protocol family 16
id:0x51152100
ACP ON!
ACP bus = 200M!
L2cache cache controller enabled
check_res_of_trace_clock: sched_clock() high resolution
Serial: dwuart driver
uart:0: ttyAMA0 at MMIO 0x1010e000 (irq = 77) is a AMBA/DW
uart:1: ttyAMA1 at MMIO 0x1010f000 (irq = 78) is a AMBA/DW
console enabled
pcie0 sel: 0x1, pcie1 sel:0x0,pcie0 memsize:0xa00000, pcie1 memsize:0xa00000.
PCIE0 Device Link Up val = 0x00008038, loop = 2.
PCI: bus0: Fast back to back transfers disabled
pci 0000:00:00.0: BAR 0: assigned
pci 0000:00:00.0: BAR 0: set to (PCI address
bio: create slab <bio-0> at 0
vgaarb: loaded
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource timer1
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 128 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
squashfs: version 4.0 (2009/01/31) Phillip Lougher
JFFS2 version 2.2. © 2001-2006 Red Hat, Inc.
msgmni has been set to 218
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
brd: module loaded
mtdoops: mtd device (mtddev=name/number) must be supplied
Spi id table Version 1.22
Spi Flash Controller V300 Device Driver, Version 1.10
Special nand id table Version 1.33
Hisilicon Nand Flash Controller V301 Device Driver, Version 1.10
Nand ID: 0x01 0xF1 0x00 0x1D 0x01 0xF1 0x00 0x1D
Nand(Hardware): Block:128KB Page:2KB Chip:128MB OOB:64B ECC:4Bytes
NAND device: Manufacturer ID: 0x01, Chip ID: 0xf1 (AMD S34ML01G1)
NAND_ECC_NONE selected by board driver. This is not recommended !!
3 cmdlinepart partitions found on MTD device hinand
Creating 3 MTD partitions on "hinand":
0x000000000000-0x000000100000 : "startcode"
0x000000100000-0x000008000000 : "ubifs"
0x000008000000-0x000008000000 : "reserved"
mtd: partition "reserved" is out of reach -- disabled
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
UBI: attached mtd1 to ubi0
UBI: MTD device name: "ubifs"
UBI: MTD device size: 127 MiB
UBI: number of good PEBs: 1015
UBI: number of bad PEBs: 1
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 512
UBI: number of internal volumes: 1
UBI: number of user volumes: 14
UBI: available PEBs: 287
UBI: total number of reserved PEBs: 728
UBI: number of PEBs reserved for bad PEB handling: 20
UBI: max/mean erase counter: 32/22
UBI: image sequence number: 1866474915
UBI: background thread "ubi_bgt0d" started, PID 36
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
CSLIP: code copyright 1989 Regents of the University of California.
SLIP linefill/keepalive option.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
hiusb_start_hcd sucessful!
hiusb-ehci hiusb-ehci.0: HIUSB EHCI
hiusb-ehci hiusb-ehci.0: new USB bus registered, assigned bus number 1
hiusb-ehci hiusb-ehci.0: irq 71, io mem 0x10a40000
hiusb-ehci hiusb-ehci.0: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
hiusb-ohci hiusb-ohci.0: HIUSB OHCI
hiusb-ohci hiusb-ohci.0: new USB bus registered, assigned bus number 2
hiusb-ohci hiusb-ohci.0: irq 70, io mem 0x10a50000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
Netfilter messages via NETLINK v0.30.
ip_tables: (C) 2000-2006 Netfilter Core Team
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 17
VFS: Mounted root (squashfs filesystem) readonly on device 31:11.
Freeing init memory: 140K
-=#DOPRA LINUX 1.0#=-
-=#EchoLife WAP 0.1#=-
-=#Huawei Technologies Co., Ltd #=-
mount file system
Loading the kernel modules:
Loading module: rng-core
Loading module: nf_conntrack
nf_conntrack version 0.5.0 (4000 buckets, 16000 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
Loading module: xt_mark
Loading module: xt_connmark
Loading module: xt_MARK
Loading module: xt_limit
Loading module: xt_state
Loading module: xt_tcpmss
Loading module: nf_nat
Loading module: ipt_MASQUERADE
Loading module: ipt_REDIRECT
Loading module: ipt_NETMAP
Loading module: nf_conntrack_ipv4.ko
Loading module: iptable_nat.ko
Making device instances:
Setting console log message level:
Setting hostname:
Settingup the sysctl configurations:
Setting up interface lo:
Running local startup scripts.
*******************************************
--== Welcome To IAS WAP ==--
--== Huawei Technologies Co., Ltd. ==--
*******************************************
IAS WAP Ver:V800R013C10SPC150B000
IAS WAP Timestamp:2013/12/28 12:35:46
*******************************************
Start init IAS WAP basic module ....
current lastword info:Add=0xc7b06000;max_num=300;Add1=0xc7b01000;Add2=0xc7b06000;Add3=0xc7b0b000;
Init IAS WAP basic module done!
soft lockup args:snap=150; release=50; dump flag=1;
UBIFS error (pid 103): mount_ubifs: fenghe.linux4.3 : space_fixup = 0
Set kmsgread process pid to:93;
Rootfs time stamp:2013-12-28_14:56:12
SVN label(ont):fuse init (API version 7.13)
SCSI subsystem initialized
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usblp
User init start......
Loading the SD5115V100 modules:
SYSCTL module is installed
PIE module is installed
GPIO module is installed
SPI module is installed
I2C module is installed
DP module is installed
MDIO module is installed
TIMER module is installed
UART module is installed
HW module is installed
ifconfig eth0 hw ether C0:70:09:73:5B:9B
Loading the EchoLife WAP modules: LDSP
COMMON For LDSP Install Successfully...
GPIO For LDSP Install Successfully...
HIGHWAY For LDSP Install Successfully...
------ SOC is 5115 T PILOT ------
<ldsp>board version is 4061
<ldsp>pcb version is 4
<ldsp>orig board version is 6
CHIPADP-SD5115 BASIC For LDSP Install Successfully...
CHIPADP-SD5115 EXT For LDSP Install Successfully...
I2C For LDSP Install Successfully...
LSW L2 For LDSP Install Successfully...
LSW L3 For LDSP Install Successfully...
DEV For LDSP Install Successfully...
:ae_chip=6,ae_chip=255,ae_chip=255,ae_chip=0
:board_ver=4061,pcb_ver=4
:Can not find topo file in /etc/wap/dm.cfg/topo_relation.cfg.
Kernel panic - not syncing: Get topo config file Error!
[<c0031da0>] (unwind_backtrace+0x0/0xfc) from [<c02d7f00>] (panic+0x60/0xd8)
[<c02d7f00>] (panic+0x60/0xd8) from [<bf1a4838>] (hw_dm_topo_init+0xe0/0xfc )
[<bf1a4838>] (hw_dm_topo_init+0xe0/0xfc ) from [<bf19d09c>] (hw_dm_init_data+0x74/0x12c )
[<bf19d09c>] (hw_dm_init_data+0x74/0x12c ) from [<bf486f44>] (init_module+0xb4/0x1fc )
[<bf486f44>] (init_module+0xb4/0x1fc ) from [<c002b5b4>] (do_one_initcall+0x30/0x1c0)
[<c002b5b4>] (do_one_initcall+0x30/0x1c0) from [<c0073ba8>] (sys_init_module+0xc4/0x1f8)
[<c0073ba8>] (sys_init_module+0xc4/0x1f8) from [<c002c0e0>] (ret_fast_syscall+0x0/0x30)
Rebooting in 3 seconds..Reset chip directly!!
Soft chip reset!!
求中断命令 电脑无法获取ip(自动固定都不行)难道只能拆焊flash？ 这个方法能有用吗 其实我的和你一样...配置更新不上了..无现的重启.... 找了好久....目前未看到有解决的办法...你还是上网找个8245的1000M的换上吧..我就是这样子弄了...实在是没有办法了...头痛呀 换8245吧.TB上卖才160左右 telnet修改，华为原厂两行obj.id = "0x0000001a" ; obj.value = "COMMON";^M
obj.id = "0x0000001b" ; obj.value = "COMMON";^M( |0 a$ H% Z+ i
改成你的省份，例如如obj.id = "0x0000001a" ; obj.value = "E8C";^M' R* B1 i( ~3 p
obj.id = "0x0000001b" ; obj.value = "BJCT";^M 这是北京，上海就是SHCT ，江苏就是JSCT ，这只适合改C 系列的光猫
页:
[1]