求助！！6328+4313芯片中兴ZXV10-W300D电信猫刷op无线有线均正常，但不能正常开机？
本帖最后由 海南风 于 2015-8-30 13:04 编辑中兴ZXV10-W300D电信猫原厂信息：
主芯片型号:963281TAN
编译时间：110407_1023
软件版本:1.0.0
引导版本:1.0.37-106.24
DSL 驱动版本：A2pD030n.d23c
无线驱动版本：5.100.96.0.cpe4.06L03.0
不少坛友有此机器，刷op可以用无线中继和lan改wan继续玩。
W300D刷入openwrt-HG100N-squashfs-cfe.bin, 无线有线均正常,lan转wan在web设置没成功，可做AP也可搜无线接入。但开机直接进入cfe，不能正常启动，需在cfe下输入r回车才启动，启动后功能正常。现附TTL信息请大神分析原因，看看怎么解决?
感谢www.openwrt.org.cn坛Kicer大神！！
刷机过程是：先有编程器将原厂编程器固件刷入8M闪存（4M也可以刷入，但不能保存设置）再在原厂固件下用TTL进入cfe，设置直接电脑IP192.168.1.100，浏览器进入web刷带cfe的腾达W150D-cn.bin固件（会刷掉电信原版的cfe，原版cfe安装op不成功），再在腾达W150D-cn的web刷Kicer高手提供的固件openwrt-HG100N-squashfs-cfe.bin在这http://www.openwrt.org.cn/bbs/forum.php?mod=viewthread&tid=12607
原厂固件、带cfe的腾达W150D-cn固件、Kicer大神HG100N-op固件、编程器读出8M-HG100N-op固件都在网盘http://pan.baidu.com/s/1i3jdInz
原厂固件TTL信息：
CPUI
L1CI
DRAM
----
PHYS
ZQDN
PHYE
DINT
LSYN
USYN
MSYN
LMBE
PASS
----
ZBSS
CODE
DATA
L12F
MAIN
CFE version 1.0.37-104.4 for BCM96328 (32bit,SP,BE)
Build Date: Mon Apr 11 18:03:41 CST 2011 (zfjimmy@SWD140)
Copyright (C) 2000-2009 Broadcom Corporation.
HS Serial flash device: name MX25L3205D, id 0xc216 size 4096KB
Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 33554432 bytes (32MB)
Boot Address: 0xb8000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Check Reset Default Hold : 0
Board Id (0-3) : 96328avng
Number of MAC Addresses (1-32) : 11
Base MAC Address : b0:75:d5:64:4f:4d
PSI Size (1-64) KBytes : 48
Main Thread Number : 0
User Password : "y2put"
WLAN SSID Paramters : "ChinaNet-RQp4,ihucydmp"
Device Serial Number : "33200B075D5644F4D"
Device Production Batch : "20100831"
Device Production Date : "20100831"
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from only image (0xb8020000) ...
Read flash at blk
Code Address: 0x80010000, Entry Address: 0x80248000
Decompression OK!
Entry at 0x80248000
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
0 buffers found.
Closing DMA Channels.
Starting program at 0x80248000
Linux version 2.6.21.5 (songlei@SWD150) (gcc version 4.2.3) #1 Fri Apr 22 15:44:00 CST 2011
HS Serial flash device: name MX25L3205D, id 0xc216 size 4096KB
96328avng prom init
CPU revision is: 0002a075
Determined physical RAM map:
memory: 01f00000 @ 00000000 (usable)
On node 0 totalpages: 7936
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 30 pages used for memmap
Normal zone: 3810 pages, LIFO batch:0
Built 1 zonelists.Total pages: 7874
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 32kB, physically tagged, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, linesize 16 bytes.
Synthesized TLB refill handler (21 instructions).
Synthesized TLB load handler fastpath (33 instructions).
Synthesized TLB store handler fastpath (33 instructions).
Synthesized TLB modify handler fastpath (32 instructions).
PID hash table entries: 128 (order: 7, 512 bytes)
Using 160.000 MHz high precision timer.
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 28900k/31744k available (1971k kernel code, 2844k reserved, 296k data, 92k init, 0k
highmem)
KLOB Pool 1 Initialized: 1048576 bytes <0x80300000 ... 0x80400000>
Calibrating delay loop... 318.46 BogoMIPS (lpj=159232)
Mount-cache hash table entries: 512
wait instruction: enabled
NET: Registered protocol family 16
Total Flash size: 4096K with 64 sectors
File system address: 0xb8020100
registering PCI controller with io_map_base unset
registering PCI controller with io_map_base unset
PCI: Bridge: 0000:01:00.0
IO window: disabled.
MEM window: 10f00000-10ffffff
PREFETCH window: disabled.
PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:01:00.0 to 64
BLOG v2.1 Initialized
NET: Registered protocol family 8
NET: Registered protocol family 20
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
squashfs: version 3.4 (2008/08/26) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
fuse init (API version 7.8)
io scheduler noop registered (default)
PPP generic driver version 2.4.2
NET: Registered protocol family 24
bcm963xx_mtd driver v1.0
brcmboard: brcm_board_init entry
SES: Button Interrupt 0x1 is enabled
SES: LED GPIO 0x8009 is enabled
*** Restore to Factory Default Setting ***
*** Restore to Factory Default Setting ***
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xb0000100 (irq = 36) is a BCM63XX
ttyS1 at MMIO 0xb0000120 (irq = 47) is a BCM63XX
bcmxtmrt: Broadcom BCM6328B0 ATM/PTM Network Device v0.3 Apr 22 2011 15:42:33
Mirror/redirect action on
u32 classifier
input device check on
Actions configured
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
6WIND/LSIIT IPv6 multicast forwarding 0.1 plus PIM-SM/SSM with *BSD API
NET: Registered protocol family 17
NET: Registered protocol family 15
Initializing MCPD Module
Ebtables v2.0 registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 92k freed
init started:BusyBox v1.00 (2011.04.22-07:45+0000) multi-call binary
BusyBox v1.00 (2011.04.22-07:45+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
Loading drivers and kernel modules...
pktflow: module license 'Proprietary' taints kernel.
Broadcom Packet Flow CacheChar Driver v2.1 Dec9 2009 10:05:58 Registered<242>
NBUFF v1.0 Initialized
Broadcom Packet Flow Cache learning via BLOG enabled.
Created Proc FS /procfs/fcache
Broadcom Packet Flow Cache registered with netdev chain
Constructed Broadcom Packet Flow Cache v2.1 Dec9 2009 10:05:56
bcmxtmcfg: bcmxtmcfg_init entry
adsl: adsl_init entry
IPv6: add_dev failed for dsl0
Broadcom BCMPROCFS v1.0 initialized
Broadcom BCM6328B0 Ethernet Network Device v0.1 Apr 22 2011 15:42:27
KLOB extended to 2 pools
KLOB extended to 3 pools
KLOB extended to 4 pools
KLOB extended to 5 pools
KLOB extended to 6 pools
KLOB extended to 7 pools
KLOB extended to 8 pools
Set RGMII delay Programming
dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
eth0: MAC Address: B0:75undefined5:64:4F:4D
eth1: MAC Address: B0:75undefined5:64:4F:4D
eth2: MAC Address: B0:75undefined5:64:4F:4D
eth3: MAC Address: B0:75undefined5:64:4F:4D
Enter ethsw_force_mii_mode()!
eth0 Link UP 100 mbps full duplex
PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:02:00.0 to 64
wl:srom not detected,using main memory mapped srom info(wombo board)
wl0: Broadcom BCM4313 802.11 Wireless Controller 5.60.104.0.cpe4.404.ct.2(WLTEST)
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
p8021ag: p8021ag_init entry
===== Release Version 4.02L.02 (build timestamp 110422_1544) =====
Adjust WLAN Configuration, has configuration , num , defaultnum
nvramRestore=1
restore param(SSID, PSK, username etc) from nvram
config saved.
nf_conntrack version 0.5.0 (248 buckets, 1984 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
iptables v1.3.8: can't initialize iptables table `filter': Table does not exist (do you
need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
enable l2tp alg
insmod: cannot insert `/lib/modules/2.6.21.5/kernel/net/netfilter/nf_conntrack_ftp.ko':
Success (17): Success
insmod: cannot insert `/lib/modules/2.6.21.5/kernel/net/ipv4/netfilter/nf_nat_ftp.ko':
Success (17): Success
/bin/logctl -r
read log from flash (uncompress: 4627 bytes, compress: 0 bytes)
udhcp server (v0.9.6) started. pid, ppid
interface atm1 does not exist!
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
interface atm2 does not exist!
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
enable port snooping failed: No such device or address
device eth0 entered promiscuous mode
br0: port 1(eth0) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
br0: port 1(eth0) entering disabled state
br0: port 1(eth0) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
ADDRCONF(NETDEV_UP): eth1: link is not ready
device eth1 entered promiscuous mode
br0: port 1(eth0) entering disabled state
br0: port 1(eth0) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
BcmAdsl_Initialize=0xC01636E8, g_pFnNotifyCallback=0xC0183CC4
udhcp handle msg...
files.c,625
files.c,625
files.c,625
DHCP server enable, backup server disable, msg src
pSdramPHY=0xA1FFFFF8, 0x114D1 0xDEADBEEF
AdslCoreSharedMemInit: shareMemAvailable=489248
AdslCoreHwReset:AdslOemDataAddr = 0xA1F69DD4
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
bcmxtmrt: MAC address: b0 75 d5 64 4f 4f
Broadcom Packet Flow Cache learning via BLOG disabled.
Broadcom Packet Flow Cache unregistered with netdev chain
Deleted Proc FS /procfs/fcache
Active<0> = <0> - <0>
Broadcom Packet Flow CacheChar Driver v2.1 Dec9 2009 10:05:58 Unregistered<242>
Destructed Broadcom Packet Flow Cache v2.1 Dec9 2009 10:05:56
Broadcom Packet Flow CacheChar Driver v2.1 Dec9 2009 10:05:58 Registered<242>
NBUFF v1.0 Initialized
Broadcom Packet Flow Cache learning via BLOG enabled.
Created Proc FS /procfs/fcache
Broadcom Packet Flow Cache registered with netdev chain
Constructed Broadcom Packet Flow Cache v2.1 Dec9 2009 10:05:56
ssk:error:19.405:mdm_getObjectPointer:3312:Could not find instance for
InternetGatewayDevice.WANDevice.{i}.WANConnectionDevice.{i}.WANIPConnection.{i}.X_CT-
COM_DHCPOPTION125.{i}. {1,1,1,1}
ssk:error:19.406:mdm_getObjectPointer:3312:Could not find instance for
InternetGatewayDevice.WANDevice.{i}.WANConnectionDevice.{i}.WANIPConnection.{i}.X_CT-
COM_DHCPOPTION60.{i}. {update igmp snooping port info
1,1,1,1}
new ServiceList
Error at net/bridge/br_ioctl.c,703 old_deviceless can't find br0
brctl cmd -p fdb:atm1:eth1
Error at net/bridge/br_ioctl.c,691 old_deviceless can't find br0
bcmxtmrt: MAC address: b0 75 d5 64 4f 50
update igmp snooping port info
brctl cmd -p fdb:atm1:eth1
Error at net/bridge/br_ioctl.c,691 old_deviceless can't find br0
Broadcom Packet Flow Cache learning via BLOG disabled.
Broadcom Packet Flow Cache unregistered with netdev chain
Deleted Proc FS /procfs/fcache
Active<0> = <0> - <0>
Broadcom Packet Flow CacheChar Driver v2.1 Dec9 2009 10:05:58 Unregistered<242>
Destructed Broadcom Packet Flow Cache v2.1 Dec9 2009 10:05:56
Broadcom Packet Flow CacheChar Driver v2.1 Dec9 2009 10:05:58 Registered<242>
NBUFF v1.0 Initialized
Broadcom Packet Flow Cache learning via BLOG enabled.
Created Proc FS /procfs/fcache
Broadcom Packet Flow Cache registered with netdev chain
Constructed Broadcom Packet Flow Cache v2.1 Dec9 2009 10:05:56
Illegal target name.
Bad chain.
Chain (null) doesn't exist.
bcmxtmrt: MAC address: b0 75 d5 64 4f 51
update igmp snooping port info
brctl cmd -p fdb:atm1:eth1
Broadcom Packet Flow Cache learning via BLOG disabled.
Broadcom Packet Flow Cache unregistered with netdev chain
Deleted Proc FS /procfs/fcache
Active<0> = <0> - <0>
Broadcom Packet Flow CacheChar Driver v2.1 Dec9 2009 10:05:58 Unregistered<242>
Destructed Broadcom Packet Flow Cache v2.1 Dec9 2009 10:05:56
Broadcom Packet Flow CacheChar Driver v2.1 Dec9 2009 10:05:58 Registered<242>
NBUFF v1.0 Initialized
Broadcom Packet Flow Cache learning via BLOG enabled.
Created Proc FS /procfs/fcache
Broadcom Packet Flow Cache registered with netdev chain
Constructed Broadcom Packet Flow Cache v2.1 Dec9 2009 10:05:56
Illegal target name.
Bad chain.
Chain (null) doesn't exist.
update igmp snooping port info
brctl enableproxymode br0 1 > /dev/null
Broadcom Packet Flow Cache learning via BLOG disabled.
Broadcom Packet Flow Cache unregistered with netdev chain
Deleted Proc FS /procfs/fcache
Active<0> = <0> - <0>
Broadcom Packet Flow CacheChar Driver v2.1 Dec9 2009 10:05:58 Unregistered<242>
Destructed Broadcom Packet Flow Cache v2.1 Dec9 2009 10:05:56
Broadcom Packet Flow CacheChar Driver v2.1 Dec9 2009 10:05:58 Registered<242>
NBUFF v1.0 Initialized
Broadcom Packet Flow Cache learning via BLOG enabled.
Created Proc FS /procfs/fcache
Broadcom Packet Flow Cache registered with netdev chain
Constructed Broadcom Packet Flow Cache v2.1 Dec9 2009 10:05:56
Illegal target name.
Bad chain.
Chain (null) doesn't exist.
iptables: No chain/target/match by that name
ip6tables v1.3.8: can't initialize ip6tables table `filter': iptables who? (do you need to
insmod?)
Perhaps ip6tables or your kernel needs to be upgraded.
iptables: No chain/target/match by that name
ip6tables v1.3.8: can't initialize ip6tables table `filter': iptables who? (do you need to
insmod?)
Perhaps ip6tables or your kernel needs to be upgraded.
iptables: No chain/target/match by that name
ip6tables v1.3.8: can't initialize ip6tables table `filter': iptables who? (do you need to
insmod?)
Perhaps ip6tables or your kernel needs to be upgraded.
iptables: No chain/target/match by that name
ip6tables v1.3.8: can't initialize ip6tables table `filter': iptables who? (do you need to
insmod?)
Perhaps ip6tables or your kernel needs to be upgraded.
iptables: No chain/target/match by that name
ip6tables v1.3.8: can't initialize ip6tables table `filter': iptables who? (do you need to
insmod?)
Perhaps ip6tables or your kernel needs to be upgraded.
iptables: No chain/target/match by that name
ip6tables v1.3.8: can't initialize ip6tables table `filter': iptables who? (do you need to
insmod?)
Perhaps ip6tables or your kernel needs to be upgraded.
killall bftpd
killall: bftpd: no process killed
iptables v1.3.8: can't initialize iptables table `nat': Table does not exist (do you need
to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
iptables v1.3.8: can't initialize iptables table `nat': Table does not exist (do you need
to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
Bad argument `tcp'
Try `iptables -h' or 'iptables --help' for more information.
Bad argument `udp'
Try `iptables -h' or 'iptables --help' for more information.
WLmngr Daemon is running
optarg=0 shmId=0
wlmngr.c::wlmngr_init@437 Adapter idx=0
Lock reading WLAN Object
wlReadMdmOne(). idx=0
reading WLAN Object, m_instance_wl = 412030
wlmdm wlReadBaseCfg enter objId=1
wlmdm wl_utils_convert_BasicDataTransmitRates_to_wlBasicRate enter basicDataTransmitRates
=54 wlBand = 2 wlgMode = 1
wlmdm wl_utils_convert_MaxBitRate_to_wlRate enter maxBitRate = Auto wlBand=2 wlgMode=1
wlmdm wlReadMimoCfg enter
wlMimoCfgObj->wlNBand=2
wlReadIntfCfg(). bss=0
wlReadAndMappingWLANSecurityConfig. wlAuthMode=psk, wlWpa=aes, wlWep=disabled, wlAuth=0.
wlmdm wlReadWLANConfWepKeyCfg enter. instanceOfWlanConfiguration=1
wlmdm wlReadWLANConfPreSharedKeyCfg enter
wlmdm wlReadWLANConfWpsCfg enter
wlmdm wlReadWLANConfMacFltCfg enter
wlReadIntfCfg(). bss=1
wlReadAndMappingWLANSecurityConfig. wlAuthMode=open, wlWpa=tkip, wlWep=disabled, wlAuth=0.
wlmdm wlReadWLANConfWepKeyCfg enter. instanceOfWlanConfiguration=2
wlmdm wlReadWLANConfPreSharedKeyCfg enter
wlmdm wlReadWLANConfWpsCfg enter
wlmdm wlReadWLANConfMacFltCfg enter
wlReadIntfCfg(). bss=2
wlReadAndMappingWLANSecurityConfig. wlAuthMode=open, wlWpa=tkip, wlWep=disabled, wlAuth=0.
wlmdm wlReadWLANConfWepKeyCfg enter. instanceOfWlanConfiguration=3
wlmdm wlReadWLANConfPreSharedKeyCfg enter
wlmdm wlReadWLANConfWpsCfg enter
wlmdm wlReadWLANConfMacFltCfg enter
wlReadIntfCfg(). bss=3
wlReadAndMappingWLANSecurityConfig. wlAuthMode=open, wlWpa=tkip, wlWep=disabled, wlAuth=0.
wlmdm wlReadWLANConfWepKeyCfg enter. instanceOfWlanConfiguration=4
wlmdm wlReadWLANConfPreSharedKeyCfg enter
wlmdm wlReadWLANConfWpsCfg enter
wlmdm wlReadWLANConfMacFltCfg enter
wlmdm wlReadStaticWdsCfg enter
wlmdm wlReadWdsCfg enter
func= web_main,line = 2152
get CMS_MSG_HTTPD_SAVE_CONFIG
wlmngr_NvramMapping enter. @1439
lanIpAddrOfDevice is 192.168.1.1
Richard, get CMS_MSG_RST_BTN_PUSHED
WEBUI Operation WPS Type is NONE, interface number is
WEBUI Operation WPS Type is NONE, interface number is
WEBUI Operation WPS Type is NONE, interface number is
WEBUI Operation WPS Type is NONE, interface number is
There is no Predefined DevicePin in CFE
WPS Device PIN = 10009321
wlmngr.c::wlmngr_setup@834 Adapter idx=0
wlctl -i wl0 phy_watchdog 0
wlmngr_genWscRandSssidPsk@2878wl_unit=0 unit=0 subunit=0 idx=0
mode_str=wl0_wps_mode
config_str=wl0_wps_config_state
ir_str=wl_wps_reg
NVRAM: wl0_wps_mode= wl_wps_reg=[] wl0_wps_config_state=
device wl0 is not a slave of br0
interface wl0.1 does not exist!
interface wl0.2 does not exist!
interface wl0.3 does not exist!
/bin/logctl -w
wlctl -i wl0 wds none
wlctl -i wl0 up
wlctl -i wl0 down
wlctl -i wl0 mbss 0
wlctl -i wl0 bss -C 0 down
wlctl -i wl0 bss -C 1 down
wlctl -i wl0 bss -C 2 down
wlctl -i wl0 bss -C 3 down
wlctl -i wl0 ssid -C 0 'C''h''i''n''a''N''e''t''-''R''Q''p''4'
Setting SSID: "ChinaNet-RQp4"
wlctl -i wl0 ssid -C 1 'C''h''i''n''a''N''e''t''-''D''B''2'
Setting SSID: "ChinaNet-DB2"
wlctl -i wl0 ssid -C 2 'C''h''i''n''a''N''e''t''-''D''B''3'
Setting SSID: "ChinaNet-DB3"
wlctl -i wl0 ssid -C 3 'C''h''i''n''a''N''e''t''-''D''B''4'
Setting SSID: "ChinaNet-DB4"
can't get Addr: Cannot assign requested address
wlctl -i wl0 cur_etheraddr B0:75undefined5:64:4F:4E2>/dev/null
wlctl -i wl0.1 cur_etheraddr 62:75:d5:64:4f:4f2>/dev/null
wlctl -i wl0.2 cur_etheraddr 62:75:d5:64:4f:4c2>/dev/null
wlctl -i wl0.3 cur_etheraddr 62:75:d5:64:4f:4d2>/dev/null
wlctl -i wl0ap 1
wlctl -i wl0 infra 1
wlctl -i wl0 closed 0
wlctl -i wl0 country CN
wlctl -i wl0band b
wlctl -i wl0 regulatory 0
wlctl -i wl0 radar 0 2>/dev/null
wlctl -i wl0 spect 0 2>/dev/null
wlctl -i wl0 nmode -1
wlctl -i wl0 mimo_bw_cap 1
wlctl -i wl0 wpa_cap -C 0 > /var/wpa_cap0
wlctl -i wl0 wpa_cap -C 0 0 2>/dev/null
wlctl -i wl0 wpa_cap -C 1 > /var/wpa_cap0
wlctl -i wl0 wpa_cap -C 1 0 2>/dev/null
wlctl -i wl0 wpa_cap -C 2 > /var/wpa_cap0
wlctl -i wl0 wpa_cap -C 2 0 2>/dev/null
wlctl -i wl0 wpa_cap -C 3 > /var/wpa_cap0
wlctl: Unsupported
atm0: no IPv6 routers present
The system is going down NOW !!
Sending SIGTERM to all processes.
Exiting Syslogd!
brctl enableproxymode br0 0 > /dev/null
Please stand by while rebooting the system.
Restarting system.（原厂固件到这里又重启，反复多次，原因不明）
HELO
CPUI
大神G100N-op固件TTL信息：
HELO
CPUI
L1CI
DRAM
----
PHYS
ZQDN
PHYE
DINT
LSYN
USYN
MSYN
LMBE
PASS
----
ZBSS
CODE
DATA
L12F
MAIN
CFE version 1.0.37-106.24 for BCM96328 (32bit,SP,BE)
Build Date: Thu Sep9 09:15:00 PDT 2010 (root@dhcp-10-12-160-156)
TTL显示信息：
Copyright (C) 2000-2009 Broadcom Corporation.
HS Serial flash device: name MX25L32, id 0xc216 size 4096KB
Total Flash size: 4096K with 1024 sectors
Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 33554432 bytes (32MB)
Boot Address: 0xb8000000
*** Break into CFE console ***
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id (0-3) : 963281TAN
Number of MAC Addresses (1-32) : 11
Base MAC Address : c8:3a:35:4b:cd:d0
PSI Size (1-64) KBytes : 48
Enable Backup PSI : 0
System Log Size (0-256) KBytes : 0
Main Thread Number : 0
web info: Waiting for connection on socket 0.
CFE> r（说明：开机只进到这，输入r后见一下信息）
Booting from only image (0xb8010000) ...
Code Address: 0x80010000, Entry Address: 0x80010000
LZMA: Prossible old LZMA format, trying to decompress..
Decompression OK!
Entry at 0x80010000
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
34 buffers found.
Closing DMA Channels.
Starting program at 0x80010000
[ 0.000000] Linux version 3.10.13 (kicer@atmel) (gcc version 4.6.4 (OpenWrt/Linaro GCC
4.6-2013.05 r38248) ) #4 Sun Sep 29 17:48:56 CST 2013
[ 0.000000] Detected Broadcom 0x6328 CPU revision b0
[ 0.000000] CPU frequency is 320 MHz
[ 0.000000] 32MB of RAM installed
[ 0.000000] registering 32 GPIOs
[ 0.000000] board_bcm963xx: Boot address 0xb8000000
[ 0.000000] board_bcm963xx: CFE version: 1.0.37-106.24
[ 0.000000] bootconsole enabled
[ 0.000000] CPU revision is: 0002a075 (Broadcom BMIPS4350)
[ 0.000000] board_bcm963xx: board name: 963281TAN
[ 0.000000] Determined physical RAM map:
[ 0.000000]memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0:
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
[ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.Total pages: 8128
[ 0.000000] Kernel command line:root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd
console=ttyS0,115200
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Memory: 28944k/32768k available (2352k kernel code, 3824k reserved, 618k
data, 228k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] Calibrating delay loop... 318.46 BogoMIPS (lpj=636928)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 512
[ 0.048000] NET: Registered protocol family 16
[ 0.276000] registering PCI controller with io_map_base unset
[ 0.288000] bio: create slab <bio-0> at 0
[ 0.296000] PCI host bridge to bus 0000:00
[ 0.300000] pci_bus 0000:00: root bus resource
[ 0.304000] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.308000] pci_bus 0000:00: No busn resource found for root bus, will use
[ 0.312000] pci 0000:00:00.0: bridge configuration invalid (), reconfiguring
[ 0.316000] pci 0000:00:00.0: BAR 8: assigned
[ 0.320000] pci 0000:01:00.0: BAR 0: assigned
[ 0.324000] pci 0000:00:00.0: PCI bridge to
[ 0.328000] pci 0000:00:00.0: bridge window
[ 0.332000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 0.336000] Switching to clocksource MIPS
[ 0.344000] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
[ 0.352000] bcma: bus0: Found chip with id 0x4313, rev 0x01 and package 0x08
[ 0.360000] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x24, class
0x0)
[ 0.368000] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x18,
class 0x0)
[ 0.376000] bcma: bus0: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x11, class 0x0)
[ 0.384000] bcm63xx_sprom_bcma: filled sprom for chip id 0x4313
[ 0.400000] bcma: bus0: Bus registered
[ 0.404000] NET: Registered protocol family 2
[ 0.412000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.420000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.424000] TCP: Hash tables configured (established 512 bind 512)
[ 0.432000] TCP: reno registered
[ 0.436000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.440000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.448000] NET: Registered protocol family 1
[ 0.456000] audit: initializing netlink socket (disabled)
[ 0.460000] type=2000 audit(0.460:1): initialized
[ 0.468000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.472000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c)
2001-2006 Red Hat, Inc.
[ 0.484000] msgmni has been set to 56
[ 0.488000] io scheduler noop registered
[ 0.492000] io scheduler deadline registered (default)
[ 0.500000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 36) is a bcm63xx_uart
[ 0.508000] console enabled, bootconsole disabled
[ 0.508000] console enabled, bootconsole disabled
[ 0.528000] m25p80 spi1.0: found mx25l3205d, expected m25p80
[ 0.532000] m25p80 spi1.0: mx25l3205d (4096 Kbytes)
[ 0.536000] bcm63xxpart: CFE boot tag found with version 6 and board type 96328avng
[ 0.544000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000
[ 0.552000] bcm63xxpart: Partition 1 is kernel offset 10100 and length 10ff00
[ 0.560000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length 2d0000
[ 0.568000] bcm63xxpart: Partition 3 is nvram offset 3f0000 and length 10000
[ 0.576000] bcm63xxpart: Partition 4 is linux offset 10000 and length 3e0000
[ 0.580000] bcm63xxpart: Spare partition is offset 3d0004 and length 1fffc
[ 0.588000] 5 bcm63xxpart partitions found on MTD device spi1.0
[ 0.596000] Creating 5 MTD partitions on "spi1.0":
[ 0.600000] 0x000000000000-0x000000010000 : "CFE"
[ 0.608000] 0x000000010100-0x000000120000 : "kernel"
[ 0.612000] mtd: partition "kernel" must either start or end on erase block boundary or
be smaller than an erase block -- forcing read-only
[ 0.628000] 0x000000120000-0x0000003f0000 : "rootfs"
[ 0.636000] mtd: partition "rootfs" set to be root filesystem
[ 0.640000] mtd: partition "rootfs_data" created automatically, ofs=0x3d0000,
len=0x20000
[ 0.652000] 0x0000003d0000-0x0000003f0000 : "rootfs_data"
[ 0.660000] 0x0000003f0000-0x000000400000 : "nvram"
[ 0.664000] 0x000000010000-0x0000003f0000 : "linux"
[ 0.716000] b53_common: found switch: BCM63xx, rev 0
[ 0.720000] bcm63xx-wdt bcm63xx-wdt:started, timer margin: 30 sec
[ 0.732000] TCP: cubic registered
[ 0.736000] NET: Registered protocol family 17
[ 0.740000] 8021q: 802.1Q VLAN Support v1.8
[ 0.756000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 0.768000] Freeing unused kernel memory: 228K (802f7000 - 80330000)
procd: Console is alive
procd: - watchdog -
[ 5.712000] usbcore: registered new interface driver usbfs
[ 5.716000] usbcore: registered new interface driver hub
[ 5.724000] usbcore: registered new device driver usb
[ 5.736000] Button Hotplug driver version 0.4.1
[ 5.832000] SCSI subsystem initialized
[ 5.848000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.860000] ehci-platform: EHCI generic platform driver
[ 5.868000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 5.888000] usbcore: registered new interface driver usb-storage
kmod: ran 26 iterations
procd: - preinit -
[ 6.136000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 1, 100Mbps, full-duplex
Press the key and hit to enter failsafe mode
mount_root: jffs2 is not ready - marker found
procd: - early -
procd: - watchdog -
procd: - init -
Please press Enter to activate this console.
[ 12.448000] NET: Registered protocol family 10
[ 12.480000] NTFS driver 2.1.30 .
[ 12.516000] nf_conntrack version 0.5.0 (455 buckets, 1820 max)
[ 12.536000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 12.596000] Linux video capture interface: v2.00
[ 12.628000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
[ 12.636000] Backport generated by backports.git backports-20130617-4-ge3220f5
[ 12.652000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 12.700000] usbcore: registered new interface driver ums-alauda
[ 12.712000] usbcore: registered new interface driver ums-cypress
[ 12.724000] usbcore: registered new interface driver ums-datafab
[ 12.732000] usbcore: registered new interface driver ums-freecom
[ 12.744000] usbcore: registered new interface driver ums-isd200
[ 12.756000] usbcore: registered new interface driver ums-jumpshot
[ 12.764000] usbcore: registered new interface driver ums-karma
[ 12.776000] usbcore: registered new interface driver ums-sddr09
[ 12.788000] usbcore: registered new interface driver ums-sddr55
[ 12.800000] usbcore: registered new interface driver ums-usbat
[ 12.824000] usbcore: registered new interface driver uvcvideo
[ 12.828000] USB Video Class driver (1.1.1)
[ 12.868000] xt_time: kernel timezone is -0000
[ 12.920000] cfg80211: Calling CRDA to update world regulatory domain
[ 12.936000] cfg80211: World regulatory domain updated:
[ 12.940000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain,
max_eirp)
[ 12.948000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 12.956000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 12.964000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 12.972000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 12.980000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.132000] PPP generic driver version 2.4.2
[ 13.144000] NET: Registered protocol family 24
[ 13.220000] brcmsmac bcma0:0: mfg 4bf core 812 rev 24 class 0 irq 31
[ 18.456000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 1, 100Mbps, full-duplex
[ 22.484000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 1, 100Mbps, full-duplex
[ 22.496000] device eth0.1 entered promiscuous mode
[ 22.500000] device eth0 entered promiscuous mode
[ 22.524000] br-lan: port 1(eth0.1) entered forwarding state
[ 22.528000] br-lan: port 1(eth0.1) entered forwarding state
[ 23.480000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[ 24.532000] br-lan: port 1(eth0.1) entered forwarding state
[ 33.516000] jffs2: Too few erase blocks (2)
procd: - init complete -
继续求助！
页:
[1]