找回密码
 注册

QQ登录

只需一步,快速开始

查看: 3037|回复: 1

HG522-C全部信息

[复制链接]
发表于 2013-3-29 22:53:01 | 显示全部楼层 |阅读模式
不知道这个能刷什么系统
CFE version 1.0.37-102.6 for BCM96358 (32bit,SP,BE)
Build Date: Fri Jan 29 10:49:25 CST 2010 (root@g40420m)
Copyright (C) 2000-2008 Broadcom Corporation.
Parallel flash device: name AM29LV320MT, id 0x2201, size 16384KB
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Boot Address 0xbe000000

Board IP address                  : 192.168.1.1:ffffff00  
Host IP address                   : 192.168.1.100  
Gateway IP address                :   
Run from flash/host (f/h)         : f  
Default host run file name        : vmlinux  
Default host flash file name      : bcm963xx_fs_kernel  
Boot delay (0-9 seconds)          : 3  
Boot image (0=latest, 1=previous) : 0  
Board Id (0-6)                    : HG522_B  
Number of MAC Addresses (1-32)    : 11  
Base MAC Address                  : 02:10:18:01:00:01  
PSI Size (1-64) KBytes            : 0  
Main Thread Number [0|1]          : 0  
*** Press any key to stop auto run (3 seconds) ***
Auto run second count down: 0
Support Double system.
Flash boot Flag: MAINSS
Boot from main system!
Decompression OK!
Entry at 0x80269018
Closing network.
Closing DMA Channels.
Starting program at 0x80269018
Linux version 2.6.8.1 (chenhui@rtu.build.huawei.com) (gcc version 3.4.2) #134 Tue May 25 20:32:26 CST 2010
Flash 0 at 0xbe000000
  Size : 16 MB
  Regions : 1
    0 : 0x00000000 - 0x00020000 * 128
CHIP96358 prom init
CPU revision is: 0002a010
Determined physical RAM map:
memory: 01fa0000 @ 00000000 (usable)
On node 0 totalpages: 8096
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 4000 pages, LIFO batch:1
  HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd
Bootting from Main System.
brcm mips: enabling icache and dcache...
Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB 2-way, linesize 16 bytes.
PID hash table entries: 128 (order 7: 1024 bytes)
Using 150.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Allocating memory for DSP module core and initialization code
Allocated DSP module memory - CORE=0x0 SIZE=0, INIT=0x0 SIZE=0
Memory: 29348k/32384k available (1896k kernel code, 2992k reserved, 504k data, 76k init, 0k highmem)
Calibrating delay loop... 299.82 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for 'wait' instruction...  unavailable.
NET: Registered protocol family 16
Can't analyze prologue code at 801e8764
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Initializing Cryptographic API
PPP generic driver version 2.4.2
NET: Registered protocol family 24
IMQ starting with 2 devices...
IMQ driver loaded successfully.
        Hooking IMQ before NAT on PREROUTING.
        Hooking IMQ after NAT on POSTROUTING.
netconsole: not configured, aborting
Using noop io scheduler
atp_mtd driver v1.0
Atp Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
Atp Physically mapped flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
l63336:Init Partition drivers/mtd_02/maps/atpbcm963xx-flash.c 101
0 block: 0x00020100 ---0x0045f000
1 block: 0x005a0000 ---0x00080000
2 block: 0x00620000 ---0x00400000
3 block: 0x00a20100 ---0x0045f000
drivers/mtd_02/maps/atpbcm963xx-flash.c 119 i=4
Creating 4 MTD partitions on "Atp Physically mapped flash":
0x00020100-0x0047f100 : "mainlinux"
mtd: partition "mainlinux" doesn't start on an erase block boundary -- force read-only
0x005a0000-0x00620000 : "defaultcfg"
0x00620000-0x00a20000 : "middware"
0x00a20100-0x00e7f100 : "slavelinux"
mtd: partition "slavelinux" doesn't start on an erase block boundary -- force read-only
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
ehci_hcd 0000:00:0a.0: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: irq 18, pci mem c0050300
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
PCI: cache line size of 32 is not supported by device 0000:00:0a.0
ehci_hcd 0000:00:0a.0: USB f.f enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
ohci_hcd 0000:00:09.0: OHCI Host Controller
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: irq 13, pci mem c0052400
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb_02/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
drivers/usb_02/serial/usb-serial.c: USB Serial support registered for Generic
usbcore: registered new driver usbserial_generic
usbcore: registered new driver usbserial
drivers/usb_02/serial/usb-serial.c: USB Serial Driver core v2.0
bhal: bhal_init entry
** support LED GPIO mode. **
SES: Button GPIO 0x8023 is enabled
SES: LED GPIO 0x8023 is enabled
bcm963xx_serial driver v2.0
u32 classifier
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Bridge firewalling registered
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 76k freed
init started: BusyBox v1.9.1 (2010-05-25 20:32:54 CST)
starting pid 71, tty '': '/etc/init.d/rcS'
Algorithmics/MIPS FPU Emulator v1.5
RCS DONE
starting pid 131, tty '': '/bin/sh'

BusyBox v1.9.1 (2010-05-25 20:32:54 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
-/bin/sh: can't access tty; job control turned off
Loading drivers and kernel modules...
atmapi: module license 'Proprietary' taints kernel.
blaadd: blaa_detect entry
adsl: adsl_init entry
Broadcom BCM6358A1 Ethernet Network Device v0.3 May 25 2010 20:31:35
Config Ethernet Switch Through MDIO Pseudo PHY Interface
eth0: MAC Address: 00:25:68:F8:54:FE
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
wl: srom not detected, using main memory mapped srom info (wombo board)
wl0: wlc_attach: use mac addr from the system pool by id: 0x776c0000
wl0: MAC Address: 00:25:68:F8:54:FF
wl0: Broadcom BCM4318 802.11 Wireless Controller 4.150.10.15.cpe2.2
fuse init (API version 7.8)
fuse distribution version: 2.7.3
Daemon: 251
eth0 Link Up, LinkState = 0x0.
Waiting for cli start!- enter the msg
|===enter the log
\TSP_DBGetPara ok ulPort = 23
|
============Start vendor config deal.============
CWMP app version: V100R002C05B018 cwmp app V1.2.3.0.0
CWMP stk version: V100R002C05B018 cwmp stk V1.2.3.0.0
bootok
Welcome Visiting Huawei  Home Gateway
Copyright by Huawei Technologies Co., Ltd.
Login:
FILE: midmsg.c, LINE: 637
        leave  Mid_MsgReg
ConfigDefaultSsl return: 0
FILE: midmsg.c, LINE: 703
        Tr069Enable  is  (1)
FILE: midmsg.c, LINE: 749
        now  I don't init  midcom, just boot tr069
not support, pacStandUse
AdslGetCfgFromDB read DB error, use default value.
atmapi: prioritize receive packets
ATM proc init !!!
atmcmd:atmcmd available
pin_string= PIN=0
accum=0
pin_string= PIN=0
accum=0
WLAN: [info] file[wlancms.c] line[475] code[0x0] WlanSetupAll start
stop wsc iWsc = 0 iLltd = 0 wps_btn = 0
WLAN: [info] file[wlancms.c] line[1255] code[0x0] WlanSetSsid:  SSID=wlancmd ssid set -i 0 'C''h''i''n''a''N''e''t''-''C''h''i''n''A''d''s''l''.''N''e''t'

WLAN: [info] file[wlancms.c] line[1255] code[0x0] WlanSetSsid:  SSID=wlancmd ssid set -i 1 'i''T''V''-''C''h''i''n''a''Q''o''s''.''C''o''m'
port_no -1 not surported, br:br0, port:wl0
device wl0 is not a slave of br0
port_no -1 not surported, br:br0, port:wl0.1
device wl0.1 is not a slave of br0
port_no -1 not surported, br:br0, port:wl0.2
interface wl0.2 does not exist!
port_no -1 not surported, br:br0, port:wl0.3
interface wl0.3 does not exist!
ifconfig: SIOCGIFFLAGS: No such device
ifconfig: SIOCGIFFLAGS: No such device
WLAN: [info] file[wlancms.c] line[538] code[0x0] WlanSetupAll Enable
ifconfig: SIOCSIFHWADDR: No such device
wlancmd: wlan driver adapter not found
ifconfig: SIOCSIFHWADDR: No such device
wlancmd: wlan driver adapter not found
wlancmd: wlan driver adapter not found
wlancmd: wlan driver adapter not found
set wlan assoc device is 32.
set wlan assoc device is 32.
set wlan assoc device is 32.
set wlan assoc device is 32.
WLAN: [info] file[wlancms.c] line[1612] code[0x0] WlanDoAdvanced entry!!!
channel 6 selected
ifconfig: SIOCGIFFLAGS: No such device
ifconfig: SIOCGIFFLAGS: No such device
device wl0 entered promiscuous mode
br0: port 1(wl0) entering learning state
br0: topology change detected, propagating
br0: port 1(wl0) entering forwarding state
device wl0.1 entered promiscuous mode
br0: port 2(wl0.1) entering learning state
br0: topology change detected, propagating
br0: port 2(wl0.1) entering forwarding state
wlan wps enabled
wps pbc mode
cmd wps mode = client-pbc
wlan_wpswsc@4428 cfg_state=[1] wsc_mode=enabled
WlMngr::startWsc: client-pbc mode
*********************************************
Wi-Fi Simple Config Application - Intel Corp.
Version: Build 1.0.5, November 19 2006
*********************************************
Created @ Apr  2 2008 18:07:39
Initializing stack...button monitor start...!
OK
Now starting stack
get mac = 00 25 68 F8 54 FF
Error, ETHCMD_ETHCONTROLPORT cannot enter ioctl
eth0.2: MAC Address: 00:25:68:F8:54:FE
eth0.3: MAC Address: 00:25:68:F8:54:FE
eth0.4: MAC Address: 00:25:68:F8:54:FE
eth0.5: MAC Address: 00:25:68:F8:54:FE
device eth0.2 entered promiscuous mode
device eth0.3 entered promiscuous mode
device eth0.4 entered promiscuous mode
device eth0.5 entered promiscuous mode
br0: port 3(eth0.2) entering learning state
br0: topology change detected, propagating
br0: port 3(eth0.2) entering forwarding state
br0: port 4(eth0.3) entering learning state
br0: topology change detected, propagating
br0: port 4(eth0.3) entering forwarding state
br0: port 5(eth0.4) entering learning state
br0: topology change detected, propagating
br0: port 5(eth0.4) entering forwarding state
br0: port 6(eth0.5) entering learning state
br0: topology change detected, propagating
br0: port 6(eth0.5) entering forwarding state
device eth0 is not a slave of br0
pvc2684d: Interface "nas_0_0_35" created sucessfully
br2684_attachvcc brvcc->vlan_id 10000, brvcc->vlan_id_wan fff
pvc2684d: Communicating over ATM 0.0.35, encapsulation: LLC
device nas_0_0_35 entered promiscuous mode
br0: port 7(nas_0_0_35) entering learning state
br0: topology change detected, propagating
br0: port 7(nas_0_0_35) entering forwarding state
pvc2684d: Interface "nas_0_0_100" created sucessfully
br2684_attachvcc brvcc->vlan_id 10000, brvcc->vlan_id_wan fff
pvc2684d: Communicating over ATM 0.0.100, encapsulation: LLC
NO UPnP @Configed Mode
******* MODE: AP with built-in Registrar and UPnP Proxy *******
WSC: Build-in Registrar, wait for start command....
WSC: Build-in Registrar, wait for start command....
device nas_0_0_100 entered promiscuous mode
br0: port 8(nas_0_0_100) entering learning state
br0: topology change detected, propagating
br0: port 8(nas_0_0_100) entering forwarding state
pvc2684d: Interface "nas_0_0_127" created sucessfully
br2684_attachvcc brvcc->vlan_id 10000, brvcc->vlan_id_wan fff
pvc2684d: Communicating over ATM 0.0.127, encapsulation: LLC
device nas_0_0_127 entered promiscuous mode
br0: port 9(nas_0_0_127) entering learning state
br0: topology change detected, propagating
br0: port 9(nas_0_0_127) entering forwarding state
pvc2684d: Interface "nas_0_8_35" created sucessfully
br2684_attachvcc brvcc->vlan_id 10000, brvcc->vlan_id_wan fff
pvc2684d: Communicating over ATM 0.8.35, encapsulation: LLC
device nas_0_8_35 entered promiscuous mode
br0: port 10(nas_0_8_35) entering learning state
br0: topology change detected, propagating
br0: port 10(nas_0_8_35) entering forwarding state
pvc2684d: Interface "nas_0_8_81" created sucessfully
br2684_attachvcc brvcc->vlan_id 10000, brvcc->vlan_id_wan fff
pvc2684d: Communicating over ATM 0.8.81, encapsulation: LLC
device nas_0_8_81 entered promiscuous mode
br0: port 11(nas_0_8_81) entering learning state
br0: topology change detected, propagating
br0: port 11(nas_0_8_81) entering forwarding state
pvc2684d: Interface "nas_0_0_32" created sucessfully
br2684_attachvcc brvcc->vlan_id 10000, brvcc->vlan_id_wan fff
pvc2684d: Communicating over ATM 0.0.32, encapsulation: LLC
device nas_0_0_32 entered promiscuous mode
br0: port 12(nas_0_0_32) entering learning state
br0: topology change detected, propagating
br0: port 12(nas_0_0_32) entering forwarding state
atp: cur kernel version:[2.6.8.1]
ip_conntrack version 2.1 (125 buckets, 1000 max) - 352 bytes per conntrack
eth0 Link Down, LinkState = 0xe.
atp: Gre conn Register OK.
atp: Gre nat Register OK.
ip_conntrack_pptp version 2.1 loaded
atp: ip_conntrack_rtsp v0.01 loading
atp: ip_nat_rtsp v0.01 loading
eth0 Link Up, LinkState = 0x0.
DNS Server version: V100R002C05B022 dns server V1.2.5.0.3
SNTP version: V100R002C05B020 sntp V1.2.3.0.0.
Current sntp process is 1274!
sh: sshd: not found
blaa_dd: port mirroring config.
blaa_dd: port mirroring config.
Stop mirror atm package to eth0.5
Read upnp enable return: 1.
Start upnp now ...
===bUsbconf=1====!
temp=0==CfgFilePath= i 4
br0: port 3(eth0.2) entering disabled state
LAN IP: 192.169.20.253
printk: 13 messages suppressed.
Challenge Authentication Protocol
Challenge Authentication Protocol
Challenge Authentication Protocol
printk: 33 messages suppressed.
SSDP server socket OK!
ATP_UPnP_Start Now...!
发表于 2015-12-7 22:06:41 | 显示全部楼层
楼主你那个HG522-c ttl怎么接的 我这个接了不行呀 按住复位键开机,ping通只显示一次,ttl接上没有任何反应呀?麻烦您了怎么办?
来自 192.168.1.100 的回复: 无法访问目标主机。
来自 192.168.1.100 的回复: 无法访问目标主机。
来自 192.168.1.100 的回复: 无法访问目标主机。
来自 192.168.1.100 的回复: 无法访问目标主机。
来自 192.168.1.100 的回复: 无法访问目标主机。
来自 192.168.1.1 的回复: 字节=32 时间<1ms TTL=100
来自 192.168.1.100 的回复: 无法访问目标主机。
请求超时。
来自 192.168.1.100 的回复: 无法访问目标主机。
来自 192.168.1.100 的回复: 无法访问目标主机。
*滑块验证:
您需要登录后才可以回帖 登录 | 注册

本版积分规则

QQ|Archiver|小黑屋|宽带技术网 |网站地图

粤公网安备 44152102000001号

GMT+8, 2024-3-29 16:33 , Processed in 0.022328 second(s), 5 queries , Redis On.

Powered by Discuz! X3.5 Licensed

Copyright © 2001-2020, Tencent Cloud.

快速回复 返回顶部 返回列表