本帖最后由 松鼠派 于 2013-3-23 20:09 编辑
今天去openwrt的下载http://downloads.openwrt.org/snapshots/trunk/brcm63xx/ 下了几个据说6328芯片用的固件,第一个失败 ,刷了第2个openwrt-96328avng-16M-flash-generic-jffs2-64k-cfe.bin 没什么错误提示,ttl那里看也算正常启动了路由猫,插入网线什么的都有提示,能ping通192.168.1.1,但用浏览器不能打开192.168.1.1,第一次用openwrt,难道默认不是80端口的么?还是我刷错了固件啊. 额.我这个是6328芯片 16Mflash 64m内存的版本
ttl截的开机数据
HELO
CPUI
L1CI
DRAM
----
PHYS
ZQDN
PHYE
DINT
LSYN
USYN
MSYN
LMBE
PASS
----
ZBSS
CODE
DATA
L12F
MAIN
CFE version 1.0.37-106.17-1 for BCM96328 (32bit,SP,BE)
Build Date: 2010-06-28 15:35:56 (wander@broadcom-eu)
Copyright (C) 2000-2009 Broadcom Corporation.
HS Serial flash device: name MX25L128, id 0xc218 size 16384KB
Total Flash size: 16384K with 4096 sectors
Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 67108864 bytes (64MB)
Boot Address: 0xb8000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id (0-7) : 96328avng
Number of MAC Addresses (1-32) : 12
Base MAC Address : 70:b9:21:40:54:48
PSI Size (1-64) KBytes : 48
Enable Backup PSI [0|1] : 0
System Log Size (0-256) KBytes : 48
Main Thread Number [0|1] : 0
Serial Number :
Voice Board Configuration (0-11) : AVNG_SI32267
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from only image (0xb8010000) ...
Code Address: 0x80010000, Entry Address: 0x80010000
LZMA: Prossible old LZMA format, trying to decompress..
Decompression OK!
Entry at 0x80010000
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
0 buffers found.
Closing DMA Channels.
Starting program at 0x80010000
[ 0.000000] Linux version 3.7.10 (openwrt@OpenWRTBuild) (gcc version 4.6.4 20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #1 Fri Mar 22 19:37:06 MST 2013
[ 0.000000] Detected Broadcom 0x6328 CPU revision 10b0
[ 0.000000] CPU frequency is 320 MHz
[ 0.000000] 64MB of RAM installed
[ 0.000000] registering 32 GPIOs
[ 0.000000] board_bcm963xx: Boot address 0xb8000000
[ 0.000000] board_bcm963xx: CFE version: 1.0.37-106.17
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0002a075 (Broadcom BMIPS4350)
[ 0.000000] board_bcm963xx: board name: 96328avng
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] Reserving 0MB of memory at 0MB for crashkernel
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
[ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] Memory: 61272k/65536k available (2390k kernel code, 4264k reserved, 683k data, 252k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] Calibrating delay loop... 318.46 BogoMIPS (lpj=636928)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 512
[ 0.044000] NET: Registered protocol family 16
[ 0.272000] registering PCI controller with io_map_base unset
[ 0.284000] bio: create slab <bio-0> at 0
[ 0.288000] PCI host bridge to bus 0000:00
[ 0.292000] pci_bus 0000:00: root bus resource [mem 0x10f00000-0x11efffff]
[ 0.296000] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.300000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.304000] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.308000] pci 0000:00:00.0: BAR 8: assigned [mem 0x10f00000-0x10ffffff]
[ 0.312000] pci 0000:01:00.0: BAR 0: assigned [mem 0x10f00000-0x10f03fff 64bit]
[ 0.316000] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 0.320000] pci 0000:00:00.0: bridge window [mem 0x10f00000-0x10ffffff]
[ 0.324000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 0.328000] Switching to clocksource MIPS
[ 0.336000] NET: Registered protocol family 2
[ 0.344000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.352000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.356000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.364000] TCP: reno registered
[ 0.368000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.372000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.380000] NET: Registered protocol family 1
[ 0.388000] audit: initializing netlink socket (disabled)
[ 0.392000] type=2000 audit(0.392:1): initialized
[ 0.400000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.404000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.416000] msgmni has been set to 119
[ 0.420000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.428000] io scheduler noop registered
[ 0.432000] io scheduler deadline registered (default)
[ 0.440000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 36) is a bcm63xx_uart
[ 0.448000] console [ttyS0] enabled, bootconsole disabled
[ 0.448000] console [ttyS0] enabled, bootconsole disabled
[ 0.464000] m25p80 spi0.0: found mx25l12805d, expected m25p80
[ 0.472000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[ 0.476000] bcm63xxpart: CFE boot tag found with version 6 and board type 96328avng
[ 0.484000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000
[ 0.492000] bcm63xxpart: Partition 1 is kernel offset 10100 and length 10ff00
[ 0.500000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length ed0000
[ 0.508000] bcm63xxpart: Partition 3 is nvram offset ff0000 and length 10000
[ 0.512000] bcm63xxpart: Partition 4 is linux offset 10000 and length fe0000
[ 0.520000] bcm63xxpart: Spare partition is offset 370004 and length c7fffc
[ 0.528000] 5 bcm63xxpart partitions found on MTD device spi0.0
[ 0.536000] Creating 5 MTD partitions on "spi0.0":
[ 0.540000] 0x000000000000-0x000000010000 : "CFE"
[ 0.548000] 0x000000010100-0x000000120000 : "kernel"
[ 0.552000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.568000] 0x000000120000-0x000000ff0000 : "rootfs"
[ 0.576000] mtd: partition "rootfs" set to be root filesystem
[ 0.584000] split_squashfs: no squashfs found in "spi0.0"
[ 0.588000] 0x000000ff0000-0x000001000000 : "nvram"
[ 0.596000] 0x000000010000-0x000000ff0000 : "linux"
[ 0.644000] b53_common: found switch: BCM63xx, rev 0
[ 0.652000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
[ 0.660000] TCP: cubic registered
[ 0.664000] NET: Registered protocol family 17
[ 0.668000] Bridge firewalling registered
[ 0.676000] 8021q: 802.1Q VLAN Support v1.8
[ 1.624000] jffs2: notice: (1) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 1.644000] VFS: Mounted root (jffs2 filesystem) readonly on device 31:2.
[ 1.656000] Freeing unused kernel memory: 252k freed
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
- init -
Please press Enter to activate this console. [ 8.580000] Compat-drivers backport release: compat-drivers-2013-01-21-1
[ 8.584000] Backport based on wireless-testing.git master-2013-02-22
[ 8.592000] compat.git: wireless-testing.git
[ 8.832000] cfg80211: Calling CRDA to update world regulatory domain
[ 8.836000] cfg80211: World regulatory domain updated:
[ 8.844000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 8.852000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 8.860000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 8.868000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 8.876000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 8.884000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.832000] Broadcom 43xx driver loaded [ Features: PNL ]
[ 9.864000] Button Hotplug driver version 0.4.1
[ 9.944000] PPP generic driver version 2.4.2
[ 10.072000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 10.332000] NET: Registered protocol family 24
[ 10.420000] nf_conntrack version 0.5.0 (961 buckets, 3844 max)
[ 14.932000] device eth0.1 entered promiscuous mode
[ 14.936000] device eth0 entered promiscuous mode
[ 14.948000] br-lan: port 1(eth0.1) entered forwarding state
[ 14.952000] br-lan: port 1(eth0.1) entered forwarding state
[ 16.956000] br-lan: port 1(eth0.1) entered forwarding state
BusyBox v1.19.4 (2013-03-22 11:35:18 MST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
BARRIER BREAKER (Bleeding Edge, r36111)
-----------------------------------------------------
* 1/2 oz Galliano Pour all ingredients into
* 4 oz cold Coffee an irish coffee mug filled
* 1 1/2 oz Dark Rum with crushed ice. Stir.
* 2 tsp. Creme de Cacao
-----------------------------------------------------
root@OpenWrt:/#
|