我插了个8187的usb网卡，可以上网，下面是内核日志，高手帮我看是什么问题
没有内置的网卡
Linux version 2.6.32.55 (lintel@EmbeddedLab) (gcc version 4.3.3 (GCC) ) #6 Wed Feb 1 01:43:45 CST 2012
Detected Broadcom 0x6358 CPU revision a1
CPU frequency is 300 MHz
32MB of RAM installed
registering 40 GPIOs
board_bcm963xx: CFE version: 1.0.37-10.3
bootconsole [early0] enabled
CPU revision is: 0002a010 (Broadcom BCM6358)
board_bcm963xx: board name: 96358VW2
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00002000
On node 0 totalpages: 8192
free_area_init_node: node 0, pgdat 80271700, node_mem_map 81000000
Normal zone: 64 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 8128 pages, LIFO batch:0
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Primary instruction cache 32kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
Memory: 29656k/32768k available (2078k kernel code, 3112k reserved, 361k data, 136k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Calibrating delay loop... 299.00 BogoMIPS (lpj=598016)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
audit: initializing netlink socket (disabled)
type=2000 audit(0.189:1): initialized
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
msgmni has been set to 57
io scheduler noop registered
io scheduler deadline registered (default)
gpiodev: gpio device registered with major 254
gpiodev: gpio platform device registered with access mask FFFFFFFF
bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
console [ttyS0] enabled, bootconsole disabled
bcm963xx_flash: 0x02000000 at 0x1e000000
bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank
bcm963xx: Found an alias at 0x1000000 for the chip at 0x0
CFI mfr 0x00000020
CFI id 0x0000227e
Amd/Fujitsu Extended Query Table at 0x0040
Amd/Fujitsu Extended Query version 1.3.
bcm963xx: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
bcm963xx_flash: Read Signature value of CFE1CFE1
bcm963xx_flash: CFE bootloader detected
bcm963xx_flash: CFE boot tag found with version 6 and board type 96358VW2
bcm963xx_flash: Partition 0 is CFE offset 0 and length 20000
bcm963xx_flash: Partition 1 is kernel offset 20100 and length dff00
bcm963xx_flash: Partition 2 is rootfs offset 100000 and length ee0000
bcm963xx_flash: Partition 3 is nvram offset fe0000 and length 20000
bcm963xx_flash: Partition 4 is linux offset 20000 and length fc0000
bcm963xx_flash: Spare partition is a20000 offset and length 5c0000
Creating 5 MTD partitions on "bcm963xx":
0x000000000000-0x000000020000 : "CFE"
0x000000020100-0x000000100000 : "kernel"
mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
0x000000100000-0x000000fe0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=A20000, len=5C0000
0x000000a20000-0x000000fe0000 : "rootfs_data"
0x000000fe0000-0x000001000000 : "nvram"
0x000000020000-0x000000fe0000 : "linux"
bcm63xx_enet MII bus: probed
bcm63xx_wdt started, timer margin: 30 sec
Registered led device: power
Registered led device: db120:power
Registered led device: dsl
Registered led device: internet
Registered led device: usb
Registered led device: wps
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 136k freed
Please be patient, while OpenWrt loads ...
input: gpio-buttons as /devices/platform/gpio-buttons.0/input/input0
Button Hotplug driver version 0.3.1
mini_fo: using base directory: /
mini_fo: using storage directory: /tmp/root
bcm63xx_enet bcm63xx_enet.0: attached PHY at address 1 [Generic PHY]
eth1: link forced UP - 100/full - flow control off/off
device eth1.0 entered promiscuous mode
device eth1 entered promiscuous mode
br-lan: port 1(eth1.0) entering forwarding state
Compat-wireless backport release: compat-wireless-2011-11-29
Backport based on wireless-testing.git master-2011-12-01
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
SCSI subsystem initialized
roboswitch: Probing device eth0: Failed to enable switch
roboswitch: Probing device eth1: found a 5325! It's a 5350.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
usbcore: registered new interface driver rt2500usb
usbcore: registered new interface driver rt73usb
usbcore: registered new interface driver rtl8187
usbcore: registered new interface driver rt2800usb
wl: module license 'unspecified' taints kernel.
Disabling lock debugging due to kernel taint
SSB/BCMA glue driver successfully attached
Slow work thread pool: Starting up
Slow work thread pool: Ready
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
NTFS driver 2.1.29 [Flags: R/O MODULE].
SGI XFS with security attributes, large block/inode numbers, no debug enabled
loop: module loaded
PPP generic driver version 2.4.2
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
PPP MPPE Compression module registered
usbcore: registered new interface driver p54usb
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
nf_conntrack version 0.5.0 (465 buckets, 1860 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
usb 1-1: new high speed USB device using bcm63xx_ehci and address 2
usb 1-1: configuration #1 chosen from 1 choice
ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
ieee80211 phy0: hwaddr 00:e0:4c:81:87:00, RTL8187BvE V0 + rtl8225z2, rfkill mask 2
rtl8187: Customer ID is 0x00
Registered led device: rtl8187-phy0::radio
Registered led device: rtl8187-phy0::tx
Registered led device: rtl8187-phy0::rx
rtl8187: wireless switch is on
xt_time: kernel timezone is -0000
IMQ driver loaded successfully.
Hooking IMQ before NAT on PREROUTING.
Hooking IMQ after NAT on POSTROUTING.
xt_opendpi 0.1 (OpenDPI wrapper module).
Netfilter messages via NETLINK v0.30.
ctnetlink v0.93: registering with nfnetlink.
ctnetlink_init: cannot register notifier.
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usbcore: registered new interface driver ath9k_htc
usbcore: registered new interface driver carl9170
usbcore: registered new interface driver cdc_acm
cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver usblp
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver zd1211rw
USB Serial support registered for cp210x
usbcore: registered new interface driver cp210x
cp210x: v0.09:Silicon Labs CP210x RS232 serial adaptor driver
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
pl2303: Prolific PL2303 USB to serial adaptor driver
fuse init (API version 7.13)
jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
jffs2_build_filesystem(): unlocking the mtd device... done.
jffs2_build_filesystem(): erasing all blocks after the end marker... done.
mini_fo: using base directory: /
mini_fo: using storage directory: /overlay
device wlan0 entered promiscuous mode
device wlan0 left promiscuous mode
br-lan: port 2(wlan0) entering disabled state
device wlan0 entered promiscuous mode
br-lan: port 2(wlan0) entering disabled state
br-lan: port 2(wlan0) entering disabled state
br-lan: port 2(wlan0) entering disabled state
br-lan: port 1(eth1.0) entering disabled state
device eth1 left promiscuous mode
device wlan0 left promiscuous mode
br-lan: port 2(wlan0) entering disabled state
device eth1.0 left promiscuous mode
br-lan: port 1(eth1.0) entering disabled state
device eth1.0 entered promiscuous mode
device eth1 entered promiscuous mode
br-lan: port 1(eth1.0) entering forwarding state
device wlan0 entered promiscuous mode
bcm63xx_enet bcm63xx_enet.0: attached PHY at address 1 [Generic PHY]
bcm63xx_enet bcm63xx_enet.0: attached PHY at address 1 [Generic PHY]
device wlan0 left promiscuous mode
br-lan: port 2(wlan0) entering disabled state
wlan0: authenticate with ec:17:2f:18:23:e2 (try 1)
wlan0: authenticated
wlan0: associate with ec:17:2f:18:23:e2 (try 1)
wlan0: RX AssocResp from ec:17:2f:18:23:e2 (capab=0x431 status=0 aid=1)
wlan0: associated
wlan0: No basic rates in AssocResp. Using min supported rate instead.
|
|Archiver|小黑屋|宽带技术网
|网站地图
发表于 2012-11-15 10:45:28