找回密码
 注册

QQ登录

只需一步,快速开始

楼主: gander

中兴ZXDSL 831CII 用tftp刷成砖了,开机POWER灯红色,求教高人!

[复制链接]
 楼主| 发表于 2014-3-31 15:39:50 | 显示全部楼层
LC  兄说的是对的,要把主机设成192.168.1网段,接上网线,到 猫的交换面端口
==

1:除了接TTL线其实也要接网线对吧?否则根本就上不了192.168.1.1(本站搜索的2个教程均没提到是否要接)
2:cef状态下不能刷不带cef的固件?刷了几次带cef的固件都提示** Flash image not found. **
后来尝试刷了个不带cef的固件貌似就砖了
3:貌似TTL线根本就不是刷机线吧,只是用来修改配置的对吧?
 楼主| 发表于 2014-3-31 16:13:10 | 显示全部楼层

用TTL  11520波特率连上后,有些乱码。电脑设成192.168.1. 10 IP后,在浏览器中,设成192.168.1.1,可以更新固件了。 更新了固件。然后,在TTL超级终端中,可以看到正常的启动文字和信息了。但在浏览器连192.168.1.1,连不了了。  电源灯还是象原来刷死时的红色。请问高手,如何处理?
 楼主| 发表于 2014-3-31 16:13:58 | 显示全部楼层
用TTL  11520波特率连上后,有些乱码。电脑设成192.168.1. 10 IP后,在浏览器中,设成192.168.1.1,可以更新固件了。 更新了固件。然后,在TTL超级终端中,可以看到正常的启动文字和信息了。但在浏览器连192.168.1.1,连不了了。  电源灯还是象原来刷死时的红色。请问高手,如何处理?
 楼主| 发表于 2014-3-31 17:00:22 | 显示全部楼层

CFE version 1.0.37-10.1 for BCM96338 (32bit,SP,BE)
Build Date: Tue Jun 22 18:10:08 CST 2010 (root@localhost.localdomain)
Copyright (C) 2000-2006 Broadcom Corporation.

Boot Address 0xbfc00000

Initializing Arena.
Initializing Devices.
Serial flash device: name EN25P16, id 0x1c14, size 2048KB
100 MB Full-Duplex (auto-neg)
CPU type 0x29010: 240MHz
Total memory: 8388608 bytes (8MB)

Total memory used by CFE:  0x80401000 - 0x805293B0 (1213360)
Initialized Data:          0x8041EAC0 - 0x80420BE0 (8480)
BSS Area:                  0x80420BE0 - 0x804273B0 (26576)
Local Heap:                0x804273B0 - 0x805273B0 (1048576)
Stack Area:                0x805273B0 - 0x805293B0 (8192)
Text (code) segment:       0x80401000 - 0x8041EABC (121532)
Boot area (physical):      0x0052A000 - 0x0056A000
Relocation Factor:         I:00000000 - D:00000000

Board IP address                  : 192.168.1.1:ffffff00  
Host IP address                   : 192.168.1.100  
Gateway IP address                :   
Run from flash/host (f/h)         : f  
Default host run file name        : vmlinux  
Default host flash file name      : bcm963xx_fs_kernel  
Boot delay (0-9 seconds)          : 1  
Board Id (0-10)                   : 96332E  
Number of MAC Addresses (1-32)    : 11  
Base MAC Address                  : c8:64:c7:75:e9:7d  
PSI Size (1-64) KBytes            : 24  

udp_send finished
No answer .auto boot ...
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 110
Booting from only image (0xbfc10000) ...
Code Address: 0x80010000, Entry Address: 0x801ac018
Decompression OK!
Entry at 0x801ac018
Closing network.
Starting program at 0x801ac018
Linux version 2.6.8.1 (root@localhost) (gcc version 3.4.2) #1 Fri Nov 21 14:49:18 CST 2008

Serial flash device: name EN25P16, id 0x1c14, size 2048KB


*** Board is not initialized properly ***


96332E prom init

CPU revision is: 00029010

Determined physical RAM map:

memory: 007a0000 @ 00000000 (usable)

On node 0 totalpages: 1952

  DMA zone: 1952 pages, LIFO batch:1

  Normal zone: 0 pages, LIFO batch:1

  HighMem zone: 0 pages, LIFO batch:1

Built 1 zonelists

Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200

brcm mips: enabling icache and dcache...

Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.

Primary data cache 8kB 2-way, linesize 16 bytes.

PID hash table entries: 32 (order 5: 256 bytes)

Using 120.000 MHz high precision timer.

Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)

Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)

Memory: 5800k/7808k available (1438k kernel code, 1988k reserved, 205k data, 68k init, 0k highmem)

Calibrating delay loop... 239.20 BogoMIPS

Mount-cache hash table entries: 512 (order: 0, 4096 bytes)

Checking for 'wait' instruction...  unavailable.

NET: Registered protocol family 16

Total Flash size: 2048K with 32 sectors

File system address: 0xbfc10100

Can't analyze prologue code at 80176274

PPP generic driver version 2.4.2

NET: Registered protocol family 24

Using noop io scheduler

bcm963xx_mtd driver v1.0

brcmboard: brcm_board_init entry

Serial: BCM63XX driver $Revision: 3.00 $

ttyS0 at MMIO 0xfffe0300 (irq = 10) is a BCM63XX

blaadd: blaa_detect entry

adsl: adsl_init entry

Broadcom BCMPROCFS v1.0 initialized

NET: Registered protocol family 2

IP: routing cache hash table of 512 buckets, 4Kbytes

TCP: Hash tables configured (established 512 bind 1024)

NET: Registered protocol family 1

NET: Registered protocol family 17

Ebtables v2.0 registered

NET: Registered protocol family 8

NET: Registered protocol family 20

802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>

All bugs added by David S. Miller <davem@redhat.com>

VFS: Mounted root (squashfs filesystem) readonly.

Freeing unused kernel memory: 68k freed


init started:  BusyBox v1.00 (2008.11.21-06:52+0000) multi-call binary
Algorithmics/MIPS FPU Emulator v1.5



BusyBox v1.00 (2008.11.21-06:52+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.


Loading drivers and kernel modules...

bcm_enet: module license 'Proprietary' taints kernel.

BCM63xx_ENET board id not set

insmod: cannot insert `/lib/modules/2.6.8.1/extra/bcm_enet.ko': Success (19): Success
BcmAdsl_Initialize=0x800EDCC8, g_pFnNotifyCallback=0x801A48C4

AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000980 adsl2=0x00000000

pSdramPHY=0xA07FFFF8, 0x22442044 0x88118811

AdslCoreHwReset: AdslOemDataAddr = 0xA07FBB54

AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000980 adsl2=0x00000000

dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered

ATM proc init !!!

ip_tables: (C) 2000-2002 Netfilter core team

ip_conntrack version 2.1 (61 buckets, 0 max) - 376 bytes per conntrack

ip_conntrack_pptp version 2.1 loaded

ip_nat_pptp version 2.0 loaded

ip_conntrack_rtsp v0.01 loading

ip_ct_h323: init success

ip_nat_h323: init success

insmod: cannot open module `/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_conntrack_tftp.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_nat_tftp.ko': No such file or directory
ip_nat_rtsp v0.01 loading


==>   Bcm963xx Software Version: ZXDSL 831CIIV5.5.2a_E09   <==

BcmRfc2684_init interface is not up nas_0_8_81!
pvc2684ctl -a -v 0.8.81 &
pvc2684d: Interface "nas_0_8_81" created sucessfully

pvc2684d: Communicating over ATM 0.8.81, encapsulation: LLC

device nas_0_8_81 entered promiscuous mode

BcmRfc2684_init interface is not up nas_0_0_35!
pvc2684ctl -a -v 0.0.35 &
pvc2684d: Interface "nas_0_0_35" created sucessfully

pvc2684d: Communicating over ATM 0.0.35, encapsulation: LLC

device nas_0_0_35 entered promiscuous mode

BcmRfc2684_init interface is not up nas_0_8_35!
pvc2684ctl -a -v 0.8.35 &
pvc2684d: Interface "nas_0_8_35" created sucessfully

pvc2684d: Communicating over ATM 0.8.35, encapsulation: LLC

device nas_0_8_35 entered promiscuous mode

BcmRfc2684_init interface is not up nas_0_0_32!
pvc2684ctl -a -v 0.0.32 &
pvc2684d: Interface "nas_0_0_32" created sucessfully

pvc2684d: Communicating over ATM 0.0.32, encapsulation: LLC

device nas_0_0_32 entered promiscuous mode

BcmRfc2684_init interface is not up nas_0_0_100!
pvc2684ctl -a -v 0.0.100 &
pvc2684d: Interface "nas_0_0_100" created sucessfully

pvc2684d: Communicating over ATM 0.0.100, encapsulation: LLC

device nas_0_0_100 entered promiscuous mode

BcmRfc2684_init interface is not up nas_0_8_36!
pvc2684ctl -a -v 0.8.36 &
pvc2684d: Interface "nas_0_8_36" created sucessfully

pvc2684d: Communicating over ATM 0.8.36, encapsulation: LLC

device nas_0_8_36 entered promiscuous mode

BcmRfc2684_init interface is not up nas_0_0_33!
pvc2684ctl -a -v 0.0.33 &
pvc2684d: Interface "nas_0_0_33" created sucessfully

pvc2684d: Communicating over ATM 0.0.33, encapsulation: LLC

device nas_0_0_33 entered promiscuous mode

 楼主| 发表于 2014-4-1 08:48:51 | 显示全部楼层
这猫发热量大。插上电没多久,主芯片就烫手。如不加散热片,稳定性不好。现主要是折腾玩下
*滑块验证:
您需要登录后才可以回帖 登录 | 注册

本版积分规则

QQ|Archiver|小黑屋|宽带技术网 |网站地图

粤公网安备 44152102000001号

GMT+8, 2024-3-29 00:15 , Processed in 0.019458 second(s), 3 queries , Redis On.

Powered by Discuz! X3.5 Licensed

Copyright © 2001-2020, Tencent Cloud.

快速回复 返回顶部 返回列表