设为首页收藏本站

宽带技术网

 找回密码
 注 册

QQ登录

只需一步,快速开始

扫一扫,访问微社区

查看: 2704|回复: 4

大家帮我看看hg255d

[复制链接]
大家帮我看看hg255d刷机后出现这种情况是怎么回事?

U-Boot 1.1.3 (May 31 2012 - 20:54:08)
SoC:Ralink APSoC(RT305x)
Memory Testing.......32768K OK.
DRAM:  32 MB
relocate_code Pointer at: 81168000
config usb..
******************************
Software System Reset Occurred
******************************
The Flash ID =0000227E
FLASH:S29GL128N, SIZE:16 MBytes SECTOR:128
S29GL128N:Set sect_size = 0x00020000
flash_protect ON: from 0xBF000000 to 0xBF023873
flash_protect ON: from 0xBF040000 to 0xBF040FFF
*** Warning - bad CRC, using default environment
______________________________________________________
|   ____                           ____              |
|  |  _ \ _ __ ___  __ _ _ __ ___ | __ )  _____  __  |
|  | | | | '__/ _ \/ _` | '_ ` _ \|  _ \ / _ \ \/ /  |
|  | |_| | | |  __/ (_| | | | | | | |_) | (_) >  <   |
|  |____/|_|  \___|\__,_|_| |_| |_|____/ \___/_/\_\  |
|                                                    |
|           http://www.openwrt.org.cn                |
|              Board:HuaWei HG255D                   |
|                                                    |
|         lintel<linte@openwrt.org.cn>               |
|____________________________________________________|
ASIC 3052_MP2 (Port5<->Phy)
Flash component: NOR Flash
Build Date:May 31 2012  Time:20:54:08
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384
##### The CPU freq = 384 MHZ ####
estimate memory size =32 Mbytes
GPIO Init:
        UARTF_SHARE_MODE:GPIO
        SPI_GPIO_MODE:GPIO
GPIO_MODE_REG status:0x1e
Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.
0
   
3: System Boot system code via Flash.
eth_register  
Eth0 (10/100-M)
enetvar=ethaddr,Eth addr:F4:C7:14:4A:C3:CB

eth_current->name = Eth0 (10/100-M)
Press Reset or WPS button to Rescue Mode...
## Booting image at bf080000 ...
   Image Name:   MIPS OpenWrt Linux-2.6.32.59
   Created:      2012-07-02  10:37:56 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    775287 Bytes = 757.1 kB
   Load Address: 80000000
   Entry Point:  80000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 32
Starting kernel ...
Linux version 2.6.32.59 (kuaner@kuaner-macbook) (gcc version 4.3.3 (GCC) ) #2 Mon Jul 2 18:37:44 CST 2012
bootconsole [early0] enabled
CPU revision is: 0001964c (MIPS 24Kc)
Ralink RT3052   id:1 rev:3 running at 384.00 MHz
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00002000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Kernel command line: console=ttyS1,57600 rootfstype=squashfs,jffs2 board=HG255D
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
Writing ErrCtl register=0005e550
Readback ErrCtl register=0005e550
Memory: 30096k/32768k available (1822k kernel code, 2672k reserved, 323k data, 132k init, 0k highmem)
SLUB: Genslabs=7, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:48
console [ttyS1] enabled, bootconsole disabled
console [ttyS1] enabled, bootconsole disabled
Calibrating delay loop... 255.59 BogoMIPS (lpj=1277952)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
MIPS: machine is HuaWei HG255D
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)  漏 2001-2006 Red Hat, Inc.
msgmni has been set to 58
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x10000500 (irq = 13) is a 16550A
serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A
physmap platform flash device: 01000000 at bf000000
physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
CFI mfr 0x00000001
CFI id  0x00002101
Amd/Fujitsu Extended Query Table at 0x0040
  Amd/Fujitsu Extended Query version 1.3.
physmap-flash.0: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
RedBoot partition parsing not available
Using physmap partition information
Creating 7 MTD partitions on "physmap-flash.0":
0x000000000000-0x000000040000 : "u-boot"
0x000000040000-0x000000060000 : "u-boot-env"
0x000000060000-0x000000080000 : "factory"
0x000000080000-0x000000180000 : "kernel"
0x000000180000-0x000001000000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=800000, len=800000
0x000000800000-0x000001000000 : "rootfs_data"
0x000000080000-0x000001000000 : "firmware"
0x000000000000-0x000001000000 : "fullflash"
Fixed MDIO Bus: probed
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
Freeing unused kernel memory: 132k freed
Please be patient, while OpenWrt loads ...
CPU 0 Unable to handle kernel paging request at virtual address c1081560, epc == 800fc3b8, ra == 800fc330
Oops[#1]:
Cpu 0
$ 0   : 00000000 80240000 c1081560 00020000
$ 4   : fffe45cc 000045cc fffe0000 819dc400
$ 8   : 81033be0 00000000 80218120 00a3b68c
$12   : 8187f194 8187f180 00000001 80212cc4
$16   : 000045cb 00000004 00000000 c114c644
$20   : 00003b2c 0000000a 000045cc c1082000
$24   : 00000002 8004c3bc                  
$28   : 819da000 819dba88 c114c000 800fc330
Hi    : 00000002
Lo    : 00000000
epc   : 800fc3b8 0x800fc3b8
    Not tainted
ra    : 800fc330 0x800fc330
Status: 10008403    KERNEL EXL IE
Cause : 00800008
BadVA : c1081560
PrId  : 0001964c (MIPS 24Kc)
Modules linked in:
Process preinit (pid: 119, threadinfo=819da000, task=81816440, tls=00000000)
Stack : 810400e8 00000002 8009a474 81906000 00000004 0000001c 0000001d 0200006d
        01f2eb00 00000000 00000000 800fb3e4 c0052912 c0051000 c005c2da 0000b2da
        00590624 015b73d6 0188fef2 00000004 000034cc 00000898 00000014 00000000
        c0051000 00000003 00000003 00000001 00000000 c114c644 c114ca68 c114c664
        00000007 8141e990 80250000 0000002d 819060b4 00000000 00000000 c005c2da
        ...
Call Trace:[<8009a474>] 0x8009a474
[<800fb3e4>] 0x800fb3e4
[<800c54b0>] 0x800c54b0
[<800c534c>] 0x800c534c
[<800c1d78>] 0x800c1d78
[<8002ec74>] 0x8002ec74
[<800c2620>] 0x800c2620
[<800c3558>] 0x800c3558
[<80049fac>] 0x80049fac
[<80052084>] 0x80052084
[<80052118>] 0x80052118
[<80052664>] 0x80052664
[<8004bb48>] 0x8004bb48
[<8004fa30>] 0x8004fa30
[<800745a4>] 0x800745a4
[<8004fe6c>] 0x8004fe6c
[<8002ec74>] 0x8002ec74
[<800647e8>] 0x800647e8
[<80064934>] 0x80064934
[<80075340>] 0x80075340
[<8007a1f4>] 0x8007a1f4
[<80079660>] 0x80079660
[<8007abdc>] 0x8007abdc
[<8007d89c>] 0x8007d89c
[<8000ad3c>] 0x8000ad3c
[<80002544>] 0x80002544

Code: 5040fffe  00832021  02e41021 <90500000> 02f41021  a0500000  8fa400bc  1080000d  26940001
Disabling lock debugging due to kernel taint
发表于 2012-9-2 14:08:24 | 显示全部楼层
俺们看不懂,只能顶啦
发表于 2012-10-16 15:38:15 | 显示全部楼层
不清楚,你出了什么问题
发表于 2013-8-6 06:56:20 | 显示全部楼层
我的HG255d也是这个问题啊,不知道楼主有没解决这个问题呢?
发表于 2013-8-6 07:51:34 | 显示全部楼层
CPU 0 Unable to handle kernel paging request at virtual address c1081560,
您需要登录后才可以回帖 登录 | 注 册

本版积分规则

QQ|Archiver|手机版|小黑屋|宽带技术网 ( 粤ICP备15054574号  

粤公网安备 44152102000001号

GMT+8, 2016-12-6 00:50 , Processed in 0.472338 second(s), 24 queries , Gzip On.

Powered by Discuz! X3.2

© 2001-2013 Comsenz Inc.

快速回复 返回顶部 返回列表