zhu1005
发表于 2014-4-21 22:52:54
cfe版本为1.0.37-102.9
选那一个board id都一样,重启。
刷带CFE的固件,成砖。
zhjook
发表于 2014-4-21 22:59:22
mxic 的芯片可能不兼容
zhjook
发表于 2014-4-21 23:02:57
zhu1005 发表于 2014-4-21 22:52
cfe版本为1.0.37-102.9
选那一个board id都一样,重启。
刷带CFE的固件,成砖。
你闪存是谁家的? mx 还是sp 的?
zhu1005
发表于 2014-4-21 23:04:54
内存是SP的S29。
zhu1005
发表于 2014-4-21 23:13:09
本帖最后由 zhu1005 于 2014-4-21 23:15 编辑
CFE version 1.0.37-102.6-7 for BCM96358 (32bit,SP,BE)
Build Date: 涓 6鏈10 16:12:41 CST 2009 (wenxing@broadcom1.comtrend.com)
Copyright (C) 2000-2008 Broadcom Corporation.
Parallel flash device id 2221 is not supported.
*** Board is not initialized properly ***
*** Upgrading NVRAM (version 0 to version 5) ***
*** Board is not initialized properly ***
Press:<enter> to use current value
'-' to go previous parameter
'.' to clear the current value
'x' to exit this command
96358VW2 ------- 0
96358VW ------- 1
96358GWVG ------- 2
96358IVWG ------- 3
96358SV ------- 4
96358ADWG ------- 5
96358G-123 ------- 6
96358A-133 ------- 7
Board Id (0-7) :^C
0A
CFE version 1.0.37-102.6-7 for BCM96358 (32bit,SP,BE)
Build Date: 涓 6鏈10 16:12:41 CST 2009 (wenxing@broadcom1.comtrend.com)
Copyright (C) 2000-2008 Broadcom Corporation.
Parallel flash device id 2221 is not supported.
*** Board is not initialized properly ***
*** Upgrading NVRAM (version 0 to version 5) ***
*** Board is not initialized properly ***
Press:<enter> to use current value
'-' to go previous parameter
'.' to clear the current value
'x' to exit this command
96358VW2 ------- 0
96358VW ------- 1
96358GWVG ------- 2
96358IVWG ------- 3
96358SV ------- 4
96358ADWG ------- 5
96358G-123 ------- 6
96358A-133 ------- 7
Board Id (0-7) :0
Number of MAC Addresses (1-32) :011
Base MAC Address :00:00:00:00:00:0000:74:14:01:5A:71
PSI Size (1-64) KBytes :24
Main Thread Number :0
Serial Number :
Invalid Serial Number: 0-9, A-Z;Try again!
Serial Number :
zhjook
发表于 2014-4-21 23:14:05
有没有重启过程前的ttl 记录,我看看原因
zhu1005
发表于 2014-4-21 23:19:44
这个刚删了,明天拿JTAG线修复后,再刷一次,到时再给分析一下!
zhjook
发表于 2014-4-21 23:23:51
不用了,你救活就好了,我估计可能是无线驱动的问题
zhu1005
发表于 2014-4-22 13:45:51
Boot Address 0xbe000000
Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
Flash Layout: Boot Kern
AuxFS Misc PSI
Flash RootFS Partition Length: 12058624
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Total memory used by CFE:0x80401000 - 0x80529850 (1214544)
Initialized Data: 0x8041E730 - 0x80421050 (10528)
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id (0-8) : 96358VW2
Number of MAC Addresses (1-32) : 11
Base MAC Address : 00:1f:a3:4d:b2:36
PSI Size (1-64) KBytes : 24
Flash Block Size (1-128) in KBytes: 128
Auxillary File System Size Percent: 25
Main Thread Number : 0
udp_send finished
No answer .auto boot ...
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Code Address: 0x066B0921, Entry Address: 0x15c64727
Failed on decompression.Corrupted image?
web info: Upload 6251361 bytes, Broadcom image format.
CFE>
Flashing CFE: .
Flashing root file system and kernel at 0xbe020000: ................................................
.
*** Image flash done *** !
Resetting board...
CFE version 1.0.37-102.6-7 for BCM96358 (32bit,SP,BE)
Build Date: 涓 6鏈10 16:12:41 CST 2009 (wenxing@broadcom1.comtrend.com)
Copyright (C) 2000-2008 Broadcom Corporation.
Parallel flash device id 2221 is not supported.
*** Board is not initialized properly ***
*** Upgrading NVRAM (version 0 to version 5) ***
*** Board is not initialized properly ***
Press:<enter> to use current value
'-' to go previous parameter
'.' to clear the current value
'x' to exit this command
96358VW2 ------- 0
96358VW ------- 1
96358GWVG ------- 2
96358IVWG ------- 3
96358SV ------- 4
96358ADWG ------- 5
96358G-123 ------- 6
96358A-133 ------- 7
zhjook
发表于 2014-4-22 14:00:25
Parallel flash device id 2221 is not supported
这句话的意思是并行闪存 不支持