重组2760U-E1的固件no cfe 完美的ASMBA+DLNA ,适用6328+4313
hg110 测试完全没问题这个固件是典型的公版固件
重组2760U-E1的固件no cfe 完美的ASMBA+DLNA,原装的是带cfe的,昨天听说有人刷的时候变砖,ttl都没有反应, 而且这个版本的cfe比较老2010年的,于是我将这个固件解包,重组成 no_cfe的 提高刷机安全性, 910n ,hg110100-ba 等6328的可以放心刷,已经测试过了,完全没有问题 , 如果喜欢这个固件usb功能的有不喜欢原始cfe的可以先刷yes东的2750U 的https://www.chinadsl.net/thread-73308-1-1.html DSL_2750U_v1.0.11_cfe_fs_kernel,这个cfe的功能比较好, cfe下可以登录tftp ,用ls dir 等命令可以查看固件内部文件,方便下载上传等等
这个是原版带cfe的 https://www.chinadsl.net/thread-68876-1-1.html
这个固件是以色列的isp bezeq定制版本,其他版本的2760u都是6358的cpu ,注意区分, 刷后,默认登录是10.0.0.138 ,用户密码 Admin,usb的功能非常完整
usb 1-1: new high speed USB device using ehci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
scsi 0:0:0:0: Direct-Access SMI USB DISK 1100 PQ: 0 ANSI: 4
usb-storage: device scan complete
sd 0:0:0:0: 30910464 512-byte hardware sectors: (15.8 GB/14.7 GiB)
sd 0:0:0:0: Write Protect is off
sd 0:0:0:0: Mode Sense: 43 00 00 00
sd 0:0:0:0: Assuming drive cache: write through
sd 0:0:0:0: Assuming drive cache: write through
sda: sda4
sd 0:0:0:0: Attached SCSI removable disk
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
FAT: invalid media value (0x01)
VFS: Can't find a valid FAT filesystem on dev sda.
FAT: utf8 is not a recommended IO charset for FAT filesystems,
(注意大小写),登录后先进入高级设置(advance setting) wan 里边把默认的两个连接删掉,再添加新的ppoe连接
在lan 局域网选项里边可以更改默认网关地址从10.0.0.138改成我们习惯的192.168.1.1
注意如果将默认网关地址从10.0.0.138改成我们习惯的192.168.1.1,需要手动设置电脑ip到192.168.1.x 后才可以登录 192.168.1.1 HELO
CPUI
L1CI
DRAM
----
PHYS
ZQDN
PHYE
DINT
LSYN
USYN
MSYN
LMBE
PASS
----
ZBSS
CODE
DATA
L12F
MAIN
CFE version 1.0.37-106.24 for BCM96328 (32bit,SP,BE)
Build Date: ?????? ?????? 21 08:38:40 UTC 2012 (legath@desk)
Copyright (C) 2000-2009 Broadcom Corporation.
HS Serial flash device: name S25FL128, id 0x0118 size 16384KB
Total Flash size: 16384K with 256 sectors
Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 67108864 bytes (64MB)
Boot Address: 0xb8000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Boot image (0=latest, 1=previous) : 0
Board Id (0-6) : 96328avng
Number of MAC Addresses (1-32) : 12
Base MAC Address : 00:0a:c2:c3:fa:a7
PSI Size (1-64) KBytes : 48
Enable Backup PSI : 1
System Log Size (0-256) KBytes : 48
Main Thread Number : 0
Voice Board Configuration (0-11): VE890
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 110
Booting from latest image (0xb8800000) ...
Code Address: 0x80010000, Entry Address: 0x80014230
Decompression OK!
Entry at 0x80014230
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
0 buffers found.
Closing DMA Channels.
Starting program at 0x80014230
Linux version 2.6.30 (arriy@localhost.localdomain) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #1 Mon Dec 6 10:59:20 CST 2010
HS Serial flash device: name S25FL128P, id 0x0118 size 16384KB
96328avng prom init
CPU revision is: 0002a075 (Broadcom4350)
Determined physical RAM map:
memory: 03f00000 @ 00000000 (usable)
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
Normal 0x00001000 -> 0x00003f00
Movable zone start PFN for each node
early_node_map active PFN ranges
0: 0x00000000 -> 0x00003f00
On node 0 totalpages: 16128
free_area_init_node: node 0, pgdat 8034df10, node_mem_map 81000000
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 94 pages used for memmap
Normal zone: 11938 pages, LIFO batch:1
Built 1 zonelists in Zone order, mobility grouping on.Total pages: 16002
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
wait instruction: enabled
Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
RCU-based detection of stalled CPUs is enabled.
NR_IRQS:128
PID hash table entries: 256 (order: 8, 1024 bytes)
console enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 60252k/64512k available (2663k kernel code, 4240k reserved, 662k data, 120k init, 0k highmem)
Calibrating delay loop... 319.48 BogoMIPS (lpj=159744)
Mount-cache hash table entries: 512
net_namespace: 812 bytes
NET: Registered protocol family 16
Total Flash size: 16384K with 256 sectors
registering PCI controller with io_map_base unset
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pci 0000:00:09.0: reg 10 32bit mmio:
pci 0000:00:0a.0: reg 10 32bit mmio:
pci 0000:01:00.0: PME# supported from D0 D3hot
pci 0000:01:00.0: PME# disabled
pci 0000:02:00.0: reg 10 64bit mmio:
pci 0000:02:00.0: supports D1 D2
pci 0000:01:00.0: PCI bridge, secondary bus 0000:02
pci 0000:01:00.0: IO window: disabled
pci 0000:01:00.0: MEM window: 0x10f00000-0x10ffffff
pci 0000:01:00.0: PREFETCH window: disabled
PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:01:00.0 to 64
BLOG v2.1 Initialized
NET: Registered protocol family 8
NET: Registered protocol family 20
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
squashfs: version 4.0 with LZMA457 ported by BRCM
NTFS driver 2.1.29 .
fuse init (API version 7.11)
msgmni has been set to 117
io scheduler noop registered (default)
pcieport-driver 0000:01:00.0: device has invalid IRQ; check vendor BIOS
PCI: Setting latency timer of device 0000:01:00.0 to 64
Driver 'sd' needs updating - please use bus_type methods
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
bcm963xx_mtd driver v1.0
File system address: 0xb8800100
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: EHCI Host Controller
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM
ehci_hcd 0000:00:0a.0: irq 50, io mem 0x10002500
ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: OHCI Host Controller
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:09.0: irq 49, io mem 0x10002600
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
brcmboard: brcm_board_init entry
SES: Button Interrupt 0x1 is enabled
SES: LED GPIO 0x8009 is enabled
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xb0000100 (irq = 36) is a BCM63XX
ttyS1 at MMIO 0xb0000120 (irq = 36) is a BCM63XX
bcmxtmrt: Broadcom BCM6328B0 ATM/PTM Network Device v0.3 Dec6 2010 10:57:12
Broadcom Logger v0.1 Dec6 2010 10:56:47
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
NET: Registered protocol family 15
Initializing MCPD Module
Ebtables v2.0 registered
ebt_time registered
ebt_ftos registered
ebt_wmm_mark registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:0.
Freeing unused kernel memory: 120k freed
usb 1-1: new high speed USB device using ehci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
init started:BusyBox v1.00 (2010.12.06-03:00+0000) multi-call binary
usbfs: unrecognised mount option "0" or missing value
usbfs: mount parameter error.
BusyBox v1.00 (2010.12.06-03:00+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
Loading drivers and kernel modules...
pktflow: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
Broadcom Packet Flow CacheChar Driver v2.1 Mar 18 2010 21:39:51 Registered<242>
NBUFF v1.0 Initialized
Broadcom Packet Flow Cache learning via BLOG enabled.
Created Proc FS /procfs/fcache
Broadcom Packet Flow Cache registered with netdev chain
Constructed Broadcom Packet Flow Cache v2.1 Mar 18 2010 21:39:50
bcmxtmcfg: bcmxtmcfg_init entry
adsl: adsl_init entry
Broadcom BCMPROCFS v1.0 initialized
Broadcom BCM6328B0 Ethernet Network Device v0.1 Dec6 2010 10:56:57
dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
eth0: MAC Address: 00:0A:C2:C3:FA:A7
eth1: MAC Address: 00:0A:C2:C3:FA:A7
eth2: MAC Address: 00:0A:C2:C3:FA:A7
eth3: MAC Address: 00:0A:C2:C3:FA:A7
eth4: MAC Address: 00:0A:C2:C3:FA:A7
LAN4 Link UP 100 mbps full duplex
LAN0 Link UP 1000 mbps full duplex
message received before monitor task is initialized kerSysSendtoMonitorTask
BCM63XX_USB USB Device not present
insmod: cannot insert `/lib/modules/2.6.30/extra/bcm_usb.ko': Success (19): Success
PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:02:00.0 to 64
wl:srom not detected,using main memory mapped srom info(wombo board)
wl:loading /etc/wlan/bcm4313_map.bin
wl0: Broadcom BCM4313 802.11 Wireless Controller 5.60.120.3.cpe4.406.0
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
Broadcom 802.1Q VLAN Interface, v0.1
===== Release Version 4.06L.01 (build timestamp 101206_1059) =====
scsi 0:0:0:0: Direct-Access SMI USB DISK 1100 PQ: 0 ANSI: 4
usb-storage: device scan complete
sd 0:0:0:0: 30910464 512-byte hardware sectors: (15.8 GB/14.7 GiB)
sd 0:0:0:0: Write Protect is off
sd 0:0:0:0: Mode Sense: 43 00 00 00
sd 0:0:0:0: Assuming drive cache: write through
sd 0:0:0:0: Assuming drive cache: write through
sda: sda4
sd 0:0:0:0: Attached SCSI removable disk
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
ifconfig: br0: error fetching interface information: Device not found
ip_tables: (C) 2000-2006 Netfilter Core Team
status = enable netBiosName=HG110 directoryName =HG110 utf8DirName=HG110 charset=utf8
br0IP=192.168.1.1br0Mask=192.168.1.0
device eth0 entered promiscuous mode
br0: port 1(eth0) entering forwarding state
device eth1 entered promiscuous mode
device eth2 entered promiscuous mode
device eth3 entered promiscuous mode
device wl0 entered promiscuous mode
WLmngr Daemon is running
optarg=0 shmId=0
br0: port 5(wl0) entering forwarding state
wlevt_init@107: opened loopback socket 4
wlevt is ready for new msg...
BcmAdsl_Initialize=0xC00E2FEC, g_pFnNotifyCallback=0xC0106A94
pSdramPHY=0xA3FFFFF8, 0x1B77A3 0xDEADBEEF
I am open &async_queue = 0xc06d853c<3>kill_fasync: bad magic number in fasync_struct!
my_timeout:Pasync_queue->magic = 0x0
wlButtonInit open gpio_fasync
success
Pasync_queue->magic = 0x4601
*** PhySdramSize got adjusted: 0x76268 => 0x8BFB0 ***
AdslCoreSharedMemInit: shareMemAvailable=475184
AdslCoreHwReset:AdslOemDataAddr = 0xA3F6C9A4
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
monitor task is initialized pid= 256
wlmngr_initCfg:dataSync:1
Line 0: xDSL G.994 training
tr143EchoCfgServer:notice:27.058:main:322:calling cmsMdm_init with shmId=0
tr143EchoCfgServer:notice:27.063:cmsMdm_init:175:entered, eid=103(tr143EchoCfgServer) shmid=0
tr143EchoCfgServer:notice:27.063:oalShm_init:135:attaching to existing shmId=0
tr143EchoCfgServer:notice:27.063:oalLck_init:114:attach existing done, semid=0
tr143EchoCfgServer:notice:27.063:cmsMem_initSharedMemPointer:133:shm pool: 0x58811b34-0x58888000
tr143EchoCfgServer:error:27.068:main:332:setupConfig error ret=-1
tr143EchoCfgServer:notice:27.073:cmsMdm_cleanup:351:entered
tr143EchoCfgServer:notice:27.073:cmsMdm_cleanup:359:done
device wl0 left promiscuous mode
br0: port 5(wl0) entering disabled state
device wl0 entered promiscuous mode
br0: port 5(wl0) entering forwarding state
wlctl: wl driver adapter not found
wlctl: wl driver adapter not found
wl0.1 (): not using net_device_ops yet
wl0.2 (): not using net_device_ops yet
wl0.3 (): not using net_device_ops yet
br0: port 5(wl0) entering disabled state
Setting SSID: "Dlink-2760U"
Setting SSID: "wl0_Guest1"
Setting SSID: "wl0_Guest2"
Setting SSID: "wl0_Guest3"
Chanspec set to 0x2b06
wlctl: Unsupported
wlctl: Unsupported
wlctl: Unsupported
httpd:error:32.172:do_cmd_cgi:316:unsupported filename /webs/ncsi
br0: port 5(wl0) entering forwarding state
device wl0 left promiscuous mode
br0: port 5(wl0) entering disabled state
device wl0 entered promiscuous mode
br0: port 5(wl0) entering forwarding state
Line 0: ADSL G.992 started
Line 0: ADSL G.992 channel analysis
Line 0: ADSL G.992 message exchange
Line 0: ADSL link down
bcmxtmcfg: XTM Link Information, portid = 0, State = DOWN, Service Support = ATM
Line 0: xDSL G.994 training
Line 0: ADSL G.992 started
Line 0: ADSL G.992 channel analysis
httpd:error:67.013:do_cmd_cgi:316:unsupported filename /webs/ncsi
httpd:error:67.019:do_cmd_cgi:316:unsupported filename /webs/ncsi
Line 0: ADSL G.992 message exchange
Line 0: ADSL link up, Path 0, us=638, ds=3594
bcmxtmcfg: XTM Link Information, portid = 0, State = UP, Service Support = ATM
(ssk) xDSL link up, Connection Type: ATM
bcmxtmrt: MAC address: 00 0a c2 c3 fa a9
: register_netdev
: register_netdev done
bcmxtmcfg: Connection UP, LinkActiveStatus=0x1, US=638000, DS=3594000
recovered previous ppp session info ppp0(4c1fcc477de3/28e3)
PPP: ppp0 Start to connect ...
tr69c:error:72.093:updateTr69cCfgInfo:744:could not build full path to 222.131.210.164
saving ppp session info ppp0(4c1fcc477de3/1711)
PPP: ppp0 Connection Up.
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1008 buckets, 4032 max)
All services associated with ppp0 is activated.
Primary DNS server = 202.106.195.68
Secondary DNS server = 202.106.46.151 测试发这个估计不支持双拨号,DSL_2750U_v1.0.11_cfe_fs_kernel 可以支持 zhjook 发表于 2013-3-29 15:22 static/image/common/back.gif
测试发这个估计不支持双拨号,DSL_2750U_v1.0.11_cfe_fs_kernel 可以支持
双拨号什么意思？支持wan吗？我的rg100a-ba也刷了2750但是如何支持wan啊 你设置两个ppoe 拨号就行了 ,我的用的同一个宽带账号,可以同时拨号 这个固件好像是不支持lan转wan口的吧，谢谢楼主的重组付出！ 以后发系统能说明一下可以LAN转WAN么？ wuxeon 发表于 2013-4-3 02:11 static/image/common/back.gif
以后发系统能说明一下可以LAN转WAN么？
说实话,我这里只能用adsl ,没有wan 接入, 所以也没有试过, lan转wan 我其他不太理解是什么功能, 是指用wan 接入直接插入lan端口就可以上网吗? zhjook 发表于 2013-4-3 23:20 static/image/common/back.gif
说实话,我这里只能用adsl ,没有wan 接入, 所以也没有试过, lan转wan 我其他不太理解是什么功能, 是指用wa ...
指接入是用网线而不是电话线，因为目前全国很多城市也都在进行宽带改造，很多人需要这功能。
一般这个bcm的通用系统都是用http://路由器IP/ethwan.cmd 的命令页面来配置。