【BCM6328】Dlink dsl-2750B Gan5.CT02W-B-DL-R4B016-AU[支持HG110]
这个是dlink 澳大利亚官网下的，用文本查看文件头，是带cfe的，最新的版本Build Date: Wed Oct 17 14:45:34 CST 2012去年10月出的，应该还是很新功能也很强大，usb 接口可以用，无线什么的都没问题 admin /admin虽然是英文，但是有设置向导，跟国内常用的方式很像，不懂的按向导提示设置ppoe 就行了
一下是启动信息
HELO
CPUI
L1CI
DRAM
CFE version 1.0.37-106.24 for BCM96328 (32bit,SP,BE)
Build Date: Wed Oct 17 14:45:34 CST 2012 (root@localhost.localdomain)
Copyright (C) 2000-2009 Broadcom Corporation.
spiclk=40000000 maxoplen=512
flash=S25FL128 size=16MB id=0x012018sector=64k
HS Serial flash device: name S25FL128, id 0x012018 size 16384KB
Total Flash size: 16384K with 256 sectors
Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 67108864 bytes (64MB)
Boot Address: 0xb8000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Boot image (0=latest, 1=previous) : 0
Board Id (0-5) : 96328avng
Number of MAC Addresses (1-32) : 22
Base MAC Address : 00:10:18:00:00:00
PSI Size (1-64) KBytes : 24
Enable Backup PSI : 0
System Log Size (0-256) KBytes : 0
Main Thread Number : 0
BigSmallImg mode : 0
Voice Board Configuration (0-5) : AVNG_SI32267
send udp message finished.
Not response, auto boot ...
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 110
Booting from latest image (0xb8010000) ...
Code Address: 0x80010000, Entry Address: 0x80014230
Decompression OK!
Entry at 0x80014230
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
67 buffers found.
Closing DMA Channels.
Starting program at 0x80014230
Linux version 2.6.30 (root@localhost.localdomain) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #2 Wed Oct 17 16:19:33 CST 2012
spiclk=40000000 maxoplen=512
flash=S25FL128 size=16MB id=0x 12018sector=64k
HS Serial flash device: name S25FL128, id 0x 12018 size 16384KB
96328avng prom init
CPU revision is: 0002a075 (Broadcom4350)
Determined physical RAM map:
memory: 03f00000 @ 00000000 (usable)
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
Normal 0x00001000 -> 0x00003f00
Movable zone start PFN for each node
early_node_map active PFN ranges
0: 0x00000000 -> 0x00003f00
On node 0 totalpages: 16128
free_area_init_node: node 0, pgdat 8035eb00, node_mem_map 81000000
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 94 pages used for memmap
Normal zone: 11938 pages, LIFO batch:1
Built 1 zonelists in Zone order, mobility grouping on.Total pages: 16002
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
wait instruction: enabled
Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
RCU-based detection of stalled CPUs is enabled.
NR_IRQS:128
PID hash table entries: 256 (order: 8, 1024 bytes)
console enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 60176k/64512k available (2847k kernel code, 4316k reserved, 546k data, 128k init, 0k highmem)
Calibrating delay loop... 319.48 BogoMIPS (lpj=159744)
Mount-cache hash table entries: 512
net_namespace: 1128 bytes
NET: Registered protocol family 16
Total Flash size: 16384K with 256 sectors
registering PCI controller with io_map_base unset
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pci 0000:00:09.0: reg 10 32bit mmio:
pci 0000:00:0a.0: reg 10 32bit mmio:
pci 0000:01:00.0: PME# supported from D0 D3hot
pci 0000:01:00.0: PME# disabled
pci 0000:02:00.0: reg 10 64bit mmio:
pci 0000:02:00.0: supports D1 D2
pci 0000:01:00.0: PCI bridge, secondary bus 0000:02
pci 0000:01:00.0: IO window: disabled
pci 0000:01:00.0: MEM window: 0x10f00000-0x10ffffff
pci 0000:01:00.0: PREFETCH window: disabled
PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:01:00.0 to 64
BLOG v3.0 Initialized
NET: Registered protocol family 8
NET: Registered protocol family 20
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
squashfs: version 4.0 with LZMA457 ported by BRCM
fuse init (API version 7.11)
msgmni has been set to 117
io scheduler noop registered (default)
pcieport-driver 0000:01:00.0: device has invalid IRQ; check vendor BIOS
PCI: Setting latency timer of device 0000:01:00.0 to 64
Driver 'sd' needs updating - please use bus_type methods
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
bcm963xx_mtd driver v1.0
File system address: 0xb8010100
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: EHCI Host Controller
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM
ehci_hcd 0000:00:0a.0: irq 50, io mem 0x10002500
ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: OHCI Host Controller
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:09.0: irq 49, io mem 0x10002600
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
brcmboard: brcm_board_init entry
SES: Button Interrupt 0x1 is enabled
SES: LED GPIO 0x800a is enabled
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xb0000100 (irq = 36) is a BCM63XX
ttyS1 at MMIO 0xb0000120 (irq = 47) is a BCM63XX
bcmxtmrt: Broadcom BCM6328B0 ATM/PTM Network Device v0.3 Oct 17 2012 14:31:11
Broadcom Logger v0.1 Oct 17 2012 14:29:46
Mirror/redirect action on
u32 classifier
input device check on
Actions configured
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
Initializing MCPD Module
Ebtables v2.0 registered
ebt_time registered
ebt_ftos registered
ebt_wmm_mark registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:0.
Freeing unused kernel memory: 128k freed
usb 1-1: new high speed USB device using ehci_hcd and address 2
*<6>usb 1-1: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
init started:BusyBox v1.00 (2012.10.17-06:36+0000) multi-call binary
BusyBox v1.00 (2012.10.17-06:36+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
Loading drivers and kernel modules...
pktflow: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
Initialized fcache state
Broadcom Packet Flow CacheChar Driver v2.2 Nov 16 2010 15:04:32 Registered<242>
Created Proc FS /procfs/fcache
Broadcom Packet Flow Cache registered with netdev chain
Broadcom Packet Flow Cache learning via BLOG enabled.
Constructed Broadcom Packet Flow Cache v2.2 Nov 16 2010 15:04:32
bcmxtmcfg: bcmxtmcfg_init entry
adsl: adsl_init entry
Broadcom BCM6328B0 Ethernet Network Device v0.1 Oct 17 2012 14:29:52
ETH Init: 180 tx BDs at 0xa3939000
ETH Init: 400 rx BDs at 0xa39f9000
ETH Init: 400 rx BDs at 0xa39fa000
dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
eth0: MAC Address: 00:10:18:00:00:00
eth1: MAC Address: 00:10:18:00:00:00
eth2: MAC Address: 00:10:18:00:00:00
eth3: MAC Address: 00:10:18:00:00:00
bcm63xx_enet_poll_timer eth0 Link UP 100 mbps full duplex
message received before monitor task is initialized kerSysSendtoMonitorTask
scsi 0:0:0:0: Direct-Access USB Mass Storage Device PQ: 0 ANSI: 0 CCS
usb-storage: device scan complete
sd 0:0:0:0: 3864576 512-byte hardware sectors: (1.97 GB/1.84 GiB)
sd 0:0:0:0: Write Protect is off
sd 0:0:0:0: Mode Sense: 03 00 00 00
sd 0:0:0:0: Assuming drive cache: write through
sd 0:0:0:0: Assuming drive cache: write through
sda: sda1
sd 0:0:0:0: Attached SCSI removable disk
cmsMsg_init error ret=9002PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:02:00.0 to 64
otp_read_pci: bad crc
wl:not strapped or invalid data
wl:srom not detected,using main memory mapped srom info(wombo board)
wl:loading /etc/wlan/bcm4313_map.bin
wl0: Broadcom BCM4313 802.11 Wireless Controller 5.60.120.11.cpe4.406.8
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
mount(/var/dev/sda1,/mnt/usb1_1,vfat,flag,) ok
echo 1 0 1000310 >>/var/msghpssk
echo 1 1 1000312 >>/var/msghpssk
cmsMsg_init error ret=9002Broadcom 802.1Q VLAN Interface, v0.1
/etc/rc_vtp2.0: not found
cmsMsg_init error ret=9002
===== Release Version 4.06L.01 (build timestamp 121017_1620) =====
try read BPSI
try read MPSI
BPSI same to MPSI
MPSI valid, load into MDM
Adjust WLAN Configuration, has configuration , num , defaultnum
Broadcom Packet Flow Cache flushing the flows
Sorry, rule does not exist.
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1008 buckets, 4032 max)
xt_time: kernel timezone is -0000
ip6_tables: (C) 2000-2006 Netfilter Core Team
ssk:error:31.194:insertModuleByIndex:431:Failed on command .
ssk:error:31.194:insertModulesWithDep:362:insmod ip6t_rt.ko FAILED in insertModuleByIndex()
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
ip6tables: No chain/target/match by that name
ip6tables: No chain/target/match by that name
ip6tables: No chain/target/match by that name
ip6tables: No chain/target/match by that name
device eth0 entered promiscuous mode
br0: port 1(eth0) entering forwarding state
ip6tables: No chain/target/match by that name
iptables: Bad rule (does a matching rule exist in that chain?)
device eth1 entered promiscuous mode
ADDRCONF(NETDEV_UP): eth1: link is not ready
iptables: Bad rule (does a matching rule exist in that chain?)
device eth2 entered promiscuous mode
ADDRCONF(NETDEV_UP): eth2: link is not ready
iptables: Bad rule (does a matching rule exist in that chain?)
device eth3 entered promiscuous mode
ADDRCONF(NETDEV_UP): eth3: link is not ready
iptables: Bad rule (does a matching rule exist in that chain?)
iptables: Bad rule (does a matching rule exist in that chain?)
iptables: Bad rule (does a matching rule exist in that chain?)
iptables: Bad rule (does a matching rule exist in that chain?)
iptables: Bad rule (does a matching rule exist in that chain?)
BcmAdsl_Initialize=0xC0103188, g_pFnNotifyCallback=0xC012CB74
pSdramPHY=0xA3FFFFF8, 0xB7983 0xDEADBEEF
*** XfaceOffset: 0x21F90 => 0x21F90 ***
*** PhySdramSize got adjusted: 0x8339C => 0x98D48 ***
AdslCoreSharedMemInit: shareMemAvailable=422544
AdslCoreHwReset:pLocSbSta=82f58000 bkupThreshold=1600
AdslCoreHwReset:AdslOemDataAddr = 0xA3F783D4
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
XTM Init: 400 rx BDs at 0xa2f24000
XTM Init: 100 rx BDs at 0xa1b43800
insmod: cannot insert `/lib/modules/2.6.30/extra/pktflow.ko': Success (17): Success
Line 0: xDSL G.994 training
message received before monitor task is initialized kerSysSendtoMonitorTask
monitor task is initialized pid= 278
br0: port 2(eth1) entering disabled state
br0: port 3(eth2) entering disabled state
br0: port 4(eth3) entering disabled state
build mount info to ssk disk:1, partition:0, msg type:0x 1000310
build mount info to ssk disk:1, partition:1, msg type:0x 1000312
recover eth forwarding.
recover eth forwarding.
WLmngr Daemon is running
optarg=0 shmId=0
WEBUI Operation WPS Type is NONE, interface number is
WEBUI Operation WPS Type is NONE, interface number is
WEBUI Operation WPS Type is NONE, interface number is
WEBUI Operation WPS Type is NONE, interface number is
There is no Predefined DevicePin in CFE
WPS Device PIN = 10086643
device wl0 is not a slave of br0
interface wl0.1 does not exist!
interface wl0.2 does not exist!
interface wl0.3 does not exist!
Setting SSID: "D-wl0.1 (): not using net_device_ops yet
Link"
Setting SSID: "D-Link_guest1"
Setting SSID: "D-wl0.2 (): not using net_device_ops yet
Link_guest2"
Setting SSID: "D-wl0.3 (): not using net_device_ops yet
Link_guest3"
wlctl: Not Permitted
wlctl: Unsupported
wlctl: Unsupported
wlctl: Unsupported
chanspec 0x2b0b selected
Reaped 1542
UPnP daemon is ready to run
Line 0: ADSL G.992 started
device wl0 entered promiscuous mode
br0: port 5(wl0) entering forwarding state
iptables: Bad rule (does a matching rule exist in that chain?)
iptables: Bad rule (does a matching rule exist in that chain?)
iptables: Bad rule (does a matching rule exist in that chain?)
iptables: Bad rule (does a matching rule exist in that chain?)
Line 0: ADSL G.992 channel analysis
Line 0: ADSL G.992 message exchange
Line 0: ADSL link down
Line 0: xDSL G.994 training
Line 0: ADSL G.992 started
Line 0: ADSL G.992 channel analysis
Line 0: ADSL link up, Bearer 0, us=638, ds=4199
bcmxtmcfg: XTM Link Information, port = 0, State = UP, Service Support = ATM
(ssk) xDSL link up, Connection Type: ATM
bcmxtmrt: MAC address: 00 10 18 00 00 02
: register_netdev
: register_netdev done
XTM Init: 400 tx BDs at 0xa2d74000
bcmxtmcfg: Connection UP, LinkActiveStatus=0x1, US=638000, DS=4199000
PPP: pppoa0 Start to connect ...
netdev path : pppoa0 -> atm0
界面截图
本帖最后由 zhjook 于 2013-3-17 16:26 编辑
是6328的 ,这两天刚刚更新了3.01版本,速度好了些 2013.3.13版本
HELO
CPUI
L1CI
DRAM
.........
CFE version 1.0.37-106.24 for BCM96328 (32bit,SP,BE)
Build Date: Wed Mar 13 16:07:26 CST 2013 (root@localhost.localdomain)
Copyright (C) 2000-2009 Broadcom Corporation.
spiclk=40000000 maxoplen=512
flash=S25FL128 size=16MB id=0x012018sector=64k
HS Serial flash device: name S25FL128, id 0x012018 size 16384KB
Total Flash size: 16384K with 256 sectors
Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 67108864 bytes (64MB)
Boot Address: 0xb8000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Boot image (0=latest, 1=previous) : 0
Board Id (0-5) : 96328ang
Number of MAC Addresses (1-32) : 12
Base MAC Address : 00:0a:00:00:00:01
PSI Size (1-64) KBytes : 48
Enable Backup PSI : 1
System Log Size (0-256) KBytes : 64
Main Thread Number : 0
BigSmallImg mode : 0
send udp message finished.
Not response, auto boot ...
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 110
Booting from latest image (0xb8010000) ...
Code Address: 0x80010000, Entry Address: 0x80014230
Decompression OK!
Entry at 0x80014230
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
149 buffers found.
Closing DMA Channels.
Starting program at 0x80014230
Linux version 2.6.30 (root@localhost.localdomain) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #1 Wed Mar 13 15:52:55 CST 2013
spiclk=40000000 maxoplen=512
flash=S25FL128 size=16MB id=0x 12018sector=64k
HS Serial flash device: name S25FL128, id 0x 12018 size 16384KB
96328ang prom init
CPU revision is: 0002a075 (Broadcom4350)
Determined physical RAM map:
memory: 03f00000 @ 00000000 (usable)
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
Normal 0x00001000 -> 0x00003f00
Movable zone start PFN for each node
early_node_map active PFN ranges
0: 0x00000000 -> 0x00003f00
On node 0 totalpages: 16128
free_area_init_node: node 0, pgdat 8035eb00, node_mem_map 81000000
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 94 pages used for memmap
Normal zone: 11938 pages, LIFO batch:1
Built 1 zonelists in Zone order, mobility grouping on.Total pages: 16002
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
wait instruction: enabled
Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
RCU-based detection of stalled CPUs is enabled.
NR_IRQS:128
PID hash table entries: 256 (order: 8, 1024 bytes)
console enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 60176k/64512k available (2847k kernel code, 4316k reserved, 546k data, 128k init, 0k highmem)
Calibrating delay loop... 319.48 BogoMIPS (lpj=159744)
Mount-cache hash table entries: 512
net_namespace: 1128 bytes
NET: Registered protocol family 16
Total Flash size: 16384K with 256 sectors
registering PCI controller with io_map_base unset
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pci 0000:00:09.0: reg 10 32bit mmio:
pci 0000:00:0a.0: reg 10 32bit mmio:
pci 0000:01:00.0: PME# supported from D0 D3hot
pci 0000:01:00.0: PME# disabled
pci 0000:02:00.0: reg 10 64bit mmio:
pci 0000:02:00.0: supports D1 D2
pci 0000:01:00.0: PCI bridge, secondary bus 0000:02
pci 0000:01:00.0: IO window: disabled
pci 0000:01:00.0: MEM window: 0x10f00000-0x10ffffff
pci 0000:01:00.0: PREFETCH window: disabled
PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:01:00.0 to 64
BLOG v3.0 Initialized
NET: Registered protocol family 8
NET: Registered protocol family 20
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
squashfs: version 4.0 with LZMA457 ported by BRCM
fuse init (API version 7.11)
msgmni has been set to 117
io scheduler noop registered (default)
pcieport-driver 0000:01:00.0: device has invalid IRQ; check vendor BIOS
PCI: Setting latency timer of device 0000:01:00.0 to 64
Driver 'sd' needs updating - please use bus_type methods
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
bcm963xx_mtd driver v1.0
File system address: 0xb8010100
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: EHCI Host Controller
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM
ehci_hcd 0000:00:0a.0: irq 50, io mem 0x10002500
ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: OHCI Host Controller
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:09.0: irq 49, io mem 0x10002600
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
brcmboard: brcm_board_init entry
SES: Button Interrupt 0x1 is enabled
SES: LED GPIO 0x800a is enabled
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xb0000100 (irq = 36) is a BCM63XX
ttyS1 at MMIO 0xb0000120 (irq = 47) is a BCM63XX
bcmxtmrt: Broadcom BCM6328B0 ATM/PTM Network Device v0.3 Mar 13 2013 15:50:00
Broadcom Logger v0.1 Mar 13 2013 15:48:14
Mirror/redirect action on
u32 classifier
input device check on
Actions configured
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
Initializing MCPD Module
Ebtables v2.0 registered
ebt_time registered
ebt_ftos registered
ebt_wmm_mark registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:0.
Freeing unused kernel memory: 128k freed
init started:BusyBox v1.00 (2013.03.13-07:55+0000) multi-call binary
BusyBox v1.00 (2013.03.13-07:55+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
Loading drivers and kernel modules...
pktflow: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
Initialized fcache state
Broadcom Packet Flow CacheChar Driver v2.2 Nov 16 2010 15:04:32 Registered<242>
Created Proc FS /procfs/fcache
Broadcom Packet Flow Cache registered with netdev chain
Broadcom Packet Flow Cache learning via BLOG enabled.
Constructed Broadcom Packet Flow Cache v2.2 Nov 16 2010 15:04:32
bcmxtmcfg: bcmxtmcfg_init entry
adsl: adsl_init entry
Broadcom BCM6328B0 Ethernet Network Device v0.1 Mar 13 2013 15:48:22
ETH Init: 180 tx BDs at 0xa3939000
ETH Init: 400 rx BDs at 0xa39da000
ETH Init: 400 rx BDs at 0xa3222000
dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
eth0: MAC Address: 00:0A:C2:C3:FA:A7
eth1: MAC Address: 00:0A:C2:C3:FA:A7
eth2: MAC Address: 00:0A:C2:C3:FA:A7
eth3: MAC Address: 00:0A:C2:C3:FA:A7
bcm63xx_enet_poll_timer eth0 Link UP 100 mbps full duplex
message received before monitor task is initialized kerSysSendtoMonitorTask
wl: high_wmark_tot=400
PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:02:00.0 to 64
wl: napimode=1
otp_read_pci: bad crc
Neither SPROM nor OTP has valid image
wl:srom/otp not programmed, using main memory mapped srom info(wombo board)
wl:loading /etc/wlan/bcm4313_vars.bin
Failed to open srom image from '/etc/wlan/bcm4313_vars.bin'.
wl:loading /etc/wlan/bcm4313_map.bin
wl0: Broadcom BCM4313 802.11 Wireless Controller 5.100.138.2001.cpe4.406.3
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
Broadcom 802.1Q VLAN Interface, v0.1
/etc/rc_vtp2.0: not found
===== Release Version 4.06L.01 (build timestamp 130313_1554) =====
try read BPSI
try read MPSI
BPSI same to MPSI
MPSI valid, load into MDM
Adjust WLAN Configuration, has configuration , num , defaultnum
Broadcom Packet Flow Cache flushing the flows
Sorry, rule does not exist.
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1008 buckets, 4032 max)
Switching back to primary dns server (0.0.0.0).
xt_time: kernel timezone is -0000
ip6_tables: (C) 2000-2006 Netfilter Core Team
ssk:error:27.090:insertModuleByIndex:431:Failed on command .
ssk:error:27.091:insertModulesWithDep:362:insmod ip6t_rt.ko FAILED in insertModuleByIndex()
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
ip6tables: No chain/target/match by that name
ip6tables: No chain/target/match by that name
ip6tables: No chain/target/match by that name
ip6tables: No chain/target/match by that name
device eth0 entered promiscuous mode
br0: port 1(eth0) entering forwarding state
ip6tables: No chain/target/match by that name
iptables: Bad rule (does a matching rule exist in that chain?)
device eth1 entered promiscuous mode
ADDRCONF(NETDEV_UP): eth1: link is not ready
iptables: Bad rule (does a matching rule exist in that chain?)
device eth2 entered promiscuous mode
ADDRCONF(NETDEV_UP): eth2: link is not ready
iptables: Bad rule (does a matching rule exist in that chain?)
device eth3 entered promiscuous mode
ADDRCONF(NETDEV_UP): eth3: link is not ready
iptables: Bad rule (does a matching rule exist in that chain?)
iptables: Bad rule (does a matching rule exist in that chain?)
iptables: Bad rule (does a matching rule exist in that chain?)
iptables: Bad rule (does a matching rule exist in that chain?)
iptables: Bad rule (does a matching rule exist in that chain?)
BcmAdsl_Initialize=0xC0103188, g_pFnNotifyCallback=0xC012CB74
pSdramPHY=0xA3FFFFF8, 0x1B7829 0x86ADBEEF
*** XfaceOffset: 0x21F90 => 0x21F90 ***
*** PhySdramSize got adjusted: 0x8339C => 0x98D48 ***
AdslCoreSharedMemInit: shareMemAvailable=422544
AdslCoreHwReset:pLocSbSta=81b68000 bkupThreshold=1600
AdslCoreHwReset:AdslOemDataAddr = 0xA3F783D4
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
XTM Init: 400 rx BDs at 0xa2cfb000
XTM Init: 100 rx BDs at 0xa2fad000
insmod: cannot insert `/lib/modules/2.6.30/extra/pktflow.ko': Success (17): Success
Line 0: xDSL G.994 training
message received before monitor task is initialized kerSysSendtoMonitorTask
monitor task is initialized pid= 248
br0: port 2(eth1) entering disabled state
br0: port 3(eth2) entering disabled state
br0: port 4(eth3) entering disabled state
recover eth forwarding.
recover eth forwarding.
GPL NetUSB up!
kc 86 : run_telnetDBGDServer start
kc223 : init_DebugD end
INFO176C: NetUSB 1.02.07, 0002061E : Jul 10 2012 17:03:28
INFO176E:AUTH SIG ISOC
INFO176F:
usbcore: registered new interface driver KC NetUSB General Driver
INFO0076:init proc : PAGE_SIZE 4096
INFO1640:infomap c1d95eb4
INFO1643:sleep to wait br0 to wake up
INFO02D0:use dev Name br0
INFO164C:sleep to wait br0 end.
INFO1665:UDP_BROAD 9303 tcpPort:625868800
INFO02D0:use dev Name br0
INFO154C: tcpConnector() started...
WLmngr Daemon is running
optarg=0 shmId=0
device wl0 is not a slave of br0
interface wl0.1 does not exist!
interface wl0.2 does not exist!
interface wl0.3 does not exist!
There is no Predefined DevicePin in CFE
WPS Device PIN = 71876160
WEBUI Operation WPS Type is NONE, interface number is
WEBUI Operation WPS Type is NONE, interface number is
WEBUI Operation WPS Type is NONE, interface number is
WEBUI Operation WPS Type is NONE, interface number is
Setting SSID: "D-Link"
Setting SSID: "D-Link_guest1"
Setting SSID: "D-Link_guest2"
Setting SSID: "D-Link_guest3"
wlctl: Unsupported
INFO1429: Bind to br0
chanspec 0x2b01 selected
INFO15B4: new connection from 192.168.1.4 : 82d049c0
INFO1EB7: new Tunnel : remote ID = STORM, length = 5
INFO13D7:new connection sbus 82e72800
V4 : C0A80104
Line 0: ADSL G.992 started
Line 0: ADSL G.992 channel analysis
device wl0 entered promiscuous mode
br0: port 5(wl0) entering forwarding state
iptables: Bad rule (does a matching rule exist in that chain?)
iptables: Bad rule (does a matching rule exist in that chain?)
iptables: Bad rule (does a matching rule exist in that chain?)
iptables: Bad rule (does a matching rule exist in that chain?)
Line 0: ADSL G.992 message exchange
Line 0: ADSL link down
Line 0: xDSL G.994 training
Line 0: ADSL G.992 started
Line 0: ADSL G.992 channel analysis
Line 0: ADSL G.992 message exchange
Line 0: ADSL link up, Bearer 0, us=638, ds=3802
bcmxtmcfg: XTM Link Information, port = 0, State = UP, Service Support = ATM
can not open /var/msghpssk(ssk) xDSL link up, Connection Type: ATM
bcmxtmrt: MAC address: 00 0a c2 c3 fa a9
: register_netdev
: register_netdev done
XTM Init: 400 tx BDs at 0xa27da000
bcmxtmcfg: Connection UP, LinkActiveStatus=0x1, US=638000, DS=3802000
recovered previous ppp session info ppp0(4c1fcc477de3/2b62)
PPP: ppp0 Start to connect ...
e254saving ppp session info ppp0(4c1fcc477de3/1a7a)
netdev path : ppp0 -> atm0
3g-mngr: not found
PPP: ppp0 Connection Up.
ssk:error:82.357:insertModuleByIndex:431:Failed on command .
ssk:error:82.358:insertModulesWithDep:362:insmod ip6t_rt.ko FAILED in insertModuleByIndex()
###reset_nf_conntrack_net_ops;499;###
Broadcom Packet Flow Cache flushing the flows
iptables: Bad rule (does a matching rule exist in that chain?)
iptables: Bad rule (does a matching rule exist in that chain?)
iptables: No chain/target/match by that name
All services associated with ppp0 is activated.
atm0: no IPv6 routers present
Intrusion -> IN=ppp0 OUT= MAC= SRC=60.173.9.130 DST=123.119.23.147 LEN=40 TOS=0x00 PREC=0x00 TTL=110 ID=256 PROTO=TCP SPT=6000 DPT=6666 WINDOW=16384 RES=0x00 SYN URGP=0 MARK=0x8000000
aaPrimary DNS server (202.106.195.68) Is Down...Switching To Secondary DNS server (202.106.46.151) for 30 seconds.
Switching back to primary dns server (202.106.195.68).
Intrusion -> IN=ppp0 OUT= MAC= SRC=123.110.166.252 DST=123.119.23.147 LEN=60 TOS=0x00 PREC=0x00 TTL=43 ID=55759 DF PROTO=TCP SPT=56374 DPT=23 WINDOW=5840 RES=0x00 SYN URGP=0 MARK=0x8000000
Intrusion -> IN=ppp0 OUT= MAC= SRC=113.4.35.224 DST=123.119.23.147 LEN=48 TOS=0x00 PREC=0x00 TTL=118 ID=15171 DF PROTO=TCP SPT=8071 DPT=5688 WINDOW=65535 RES=0x00 SYN URGP=0 MARK=0x8000000
Intrusion -> IN=ppp0 OUT= MAC= SRC=113.4.35.224 DST=123.119.23.147 LEN=48 TOS=0x00 PREC=0x00 TTL=118 ID=16452 DF PROTO=TCP SPT=8071 DPT=5688 WINDOW=65535 RES=0x00 SYN URGP=0 MARK=0x8000000
Intrusion -> IN=ppp0 OUT= MAC= SRC=60.173.26.179 DST=123.119.23.147 LEN=40 TOS=0x00 PREC=0x00 TTL=110 ID=256 PROTO=TCP SPT=6000 DPT=6667 WINDOW=16384 RES=0x00 SYN URGP=0 MARK=0x8000000
这个是6328的u对吧。 是6328的 ,这两天刚刚更新了3.01版本,速度好了些 2013.3.13版本 usb那里有什么功能 设置?
usb 用处不大,用来差3g 模块的 还以为能扩展脱机下载的... 楼主，rg100a-ba刷这个很好用，但找了两天找不到wds或者ap的设置，腾达的路由和这个wds一直组不上，求救 请问是直刷还是线刷？ 风神一笑 发表于 2013-3-19 13:34 static/image/common/back.gif
楼主，rg100a-ba刷这个很好用，但找了两天找不到wds或者ap的设置，腾达的路由和这个wds一直组不上，求救
没办法, 没有完美的, 2750b B版有SMBA功能 usb 可以在网上邻居里边打开,不过就是无线不能用, 没有完美的