引导信息(出错) 第240行开始
CFE version 1.0.37-10.3 for BCM96358 (32bit,SP,BE)
Build Date: Thu May 10 22:28:34 CST 2007 (root@localhost.localdomain)
Copyright (C) 2000-2006 Broadcom Corporation.
Boot Address 0xbe000000
Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
Flash Layout: Boot Kern
AuxFS Misc PSI
Flash RootFS Partition Length: 14942208
Auto-negotiation timed-out
10 MB Half-Duplex (assumed)
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 67108864 bytes (64MB)
Total memory used by CFE:0x80401000 - 0x80528200 (1208832)
Initialized Data: 0x8041DA80 - 0x8041FA20 (8096)
BSS Area: 0x8041FA20 - 0x80426200 (26592)
Local Heap: 0x80426200 - 0x80526200 (1048576)
Stack Area: 0x80526200 - 0x80528200 (8192)
Text (code) segment: 0x80401000 - 0x8041DA80 (117376)
Boot area (physical): 0x00529000 - 0x00569000
Relocation Factor: I:00000000 - D:00000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Boot image (0=latest, 1=previous) : 0
Board Id (0-8) : 96358VW2
Number of MAC Addresses (1-32) : 10
Base MAC Address : 00:1f:a3:11:fd:11
PSI Size (1-64) KBytes : 64
Flash Block Size (1-128) in KBytes: 64
Auxillary File System Size Percent: 8
Main Thread Number : 0
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from latest image (0xbe740000) ...
Code Address: 0x80010000, Entry Address: 0x80263018
Decompression OK!
Entry at 0x80263018
Closing network.
Starting program at 0x80263018
Linux version 2.6.8.1 (root@linuxserver) (gcc version 3.4.2) #1 Sat Apr 11 15:06:44 HKT 2009
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
96358VW2 prom init
CPU revision is: 0002a010
Determined physical RAM map:
memory: 03fa0000 @ 00000000 (usable)
On node 0 totalpages: 16288
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 12192 pages, LIFO batch:2
HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB 2-way, linesize 16 bytes.
PID hash table entries: 256 (order 8: 2048 bytes)
Using 150.000 MHz high precision timer.
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 61812k/65152k available (1948k kernel code, 3272k reserved, 427k data, 80k init, 0k highmem)
Calibrating delay loop... 299.00 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for 'wait' instruction...unavailable.
NET: Registered protocol family 16
Computing partition layout for flash of size sectors
Flash split 8% into RootFS+Kernel : AuxFS
Partition ROOTFS_KRN Blks
SubPartition Image 1 Blks[ 57: 1 ..57]
SubPartition Image 2 Blks[ 57:58 .. 114]
Blk# BlkOff Blks BlkSize AvailSize MemStart MemLen Partition Name
0 1408 1131072 131072 0xbe000580 1024 BOOTLOADER
1 011413107214942208 0xbe020000 14942208 ROOTFS_KRN
115 0 11131072 1441792 0xbee60000 1441792 JFFS_AUXFS
126 0 1131072 131072 0xbefc0000 131072 LOG_SCRPAD
12765536 1131072 131072 0xbeff0000 65536 PERSISTMEM
Can't analyze prologue code at 801f59f4
SCSI subsystem initialized
usbcore: registered new driver hub
TC classifier action (bugs to netdev@oss.sgi.com cc hadi@cyberus.ca)
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Initializing Cryptographic API
PPP generic driver version 2.4.2
NET: Registered protocol family 24
Using noop io scheduler
bcm963xx_mtd driver v2.0
File system address: 0xbe740100
Registered device mtd dev Flash
Registered device mtd dev Flash
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
ehci_hcd 0000:00:0a.0: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: irq 18, pci mem c0050300
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
PCI: cache line size of 32 is not supported by device 0000:00:0a.0
ehci_hcd 0000:00:0a.0: USB f.f enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
ohci_hcd 0000:00:09.0: OHCI Host Controller
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: irq 13, pci mem c0052400
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbnet
brcmboard: brcm_board_init entry
SES: Button Interrupt 0x3 is enabled
SES: LED GPIO 0xc007 is enabled
no exited Gpio, no found Gpio To Name
no exited Gpio, no found Gpio To Name
no exited Gpio, no found Gpio To Name
no exited Gpio, no found Gpio To Name
no exited Gpio, no found Gpio To Name
no exited Gpio, no found Gpio To Name
no exited Gpio, no found Gpio To Name
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xfffe0100 (irq = 10) is a BCM63XX
ttyS1 at MMIO 0xfffe0120 (irq = 11) is a BCM63XX
Mirror/redirect action on
u32 classifier
input device check on
Actions configured
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 8192)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 80k freed
init started:BusyBox v1.00 (2009.04.12-01:52+0000) multi-call binary
Algorithmics/MIPS FPU Emulator v1.5
Using /etc/samba/smb.conf
Using /etc/samba/smb.passwd
Binaries taken from PATH
BusyBox v1.00 (2009.04.12-01:52+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
Loading drivers and kernel modules...
atmapi: module license 'Proprietary' taints kernel.
adsl: adsl_init entry
blaadd: blaa_detect entry
Broadcom BCMPROCFS v1.0 initialized
Broadcom BCM6358A1 Ethernet Network Device v0.3 Apr 11 2009 15:05:21
Config Internal PHY Through MDIO
BCM63xx_ENET: Auto-negotiation timed-out
BCM63xx_ENET: 10 MB Half-Duplex (assumed)
eth0: MAC Address: 00:1F:A3:11:FD:11
Broadcom BCM6358A1 Ethernet Network Device v0.3 Apr 11 2009 15:05:21
Config Ethernet Switch Through MDIO Pseudo PHY Interface
dgasp: kerSysRegisterDyingGaspHandler: eth1 registered
eth1: MAC Address: 00:1F:A3:11:FD:12
Broadcom BCM6358A1 USB Network Device v0.4 Apr 11 2009 15:05:22
usb0: MAC Address: 00 1F A3 11 FD 13
usb0: Host MAC Address: 00 1F A3 11 FD 14
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
wl: srom not detected, using main memory mapped srom info (wombo board)
Unable to load '/etc/wlan/bcm4318_map.bin'.
Unable to load '/etc/wlan/bcm4318_map.bin'.
wl%d: 4.150.10.15.cpe2.2 driver failed with code 11
unregister_netdevice: device wl%d/83b58820 never was registered
eth1 Link UP.
BcmAdsl_Initialize=0xC00BA3F8, g_pFnNotifyCallback=0xC00D33C4
AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000980 adsl2=0x00000000
pSdramPHY=0xA3FFFFF8, 0x2008 0x8098C0
AdslCoreHwReset: AdslOemDataAddr = 0xA3FFD3D4
AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000980 adsl2=0x00000000
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
ATM proc init !!!
==> Bcm963xx Software Version: 3.15L.bcm5358.A2pB022g.d20e-310CT0901200805082209 <==
device usb0 entered promiscuous mode
br0: port 1(usb0) entering learning state
br0: topology change detected, propagating
br0: port 1(usb0) entering forwarding state
device eth0 entered promiscuous mode
br0: port 2(eth0) entering learning state
br0: topology change detected, propagating
br0: port 2(eth0) entering forwarding state
eth1.2: MAC Address: 00:1F:A3:11:FD:12
eth1.3: MAC Address: 00:1F:A3:11:FD:12
eth1.4: MAC Address: 00:1F:A3:11:FD:12
SIOCSIFFLAGS: Network is down
SIOCSIFFLAGS: Network is down
SIOCSIFFLAGS: Network is down
device usb0 left promiscuous mode
br0: port 1(usb0) entering disabled state
device eth0 left promiscuous mode
br0: port 2(eth0) entering disabled state
device usb0 entered promiscuous mode
br0: port 1(usb0) entering learning state
br0: topology change detected, propagating
br0: port 1(usb0) entering forwarding state
device eth0 entered promiscuous mode
br0: port 2(eth0) entering learning state
br0: topology change detected, propagating
br0: port 2(eth0) entering forwarding state
device eth1.2 entered promiscuous mode
br0: port 3(eth1.2) entering learning state
br0: topology change detected, propagating
br0: port 3(eth1.2) entering forwarding state
device eth1.3 entered promiscuous mode
br0: port 4(eth1.3) entering learning state
br0: topology change detected, propagating
br0: port 4(eth1.3) entering forwarding state
device eth1.4 entered promiscuous mode
br0: port 5(eth1.4) entering learning state
br0: topology change detected, propagating
br0: port 5(eth1.4) entering forwarding state
iptables v1.2.11: can't initialize iptables table `filter': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
iptables v1.2.11: can't initialize iptables table `filter': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
ipt_hashlimit: Unknown symbol ipt_register_match
ipt_hashlimit: Unknown symbol ipt_unregister_match
insmod: cannot insert `/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ipt_hashlimit.ko': Success (2): Success
iptables v1.2.11: can't initialize iptables table `filter': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
br0: port 2(eth0) entering disabled state
br0: port 4(eth1.3) entering disabled state
br0: port 5(eth1.4) entering disabled state
br0: port 1(usb0) entering disabled state
R100A-AA能不能用啊?如果去掉CFE的话,不要TTL也可以刷吗?请那位大侠搞定后给个教程吧!
学习一下，我的GW就快到货了{{gangzai9{{
支持。
期待编译的方法说明，让更多人来改善这个FW。O(∩_∩)O谢谢
引导信息(出错) 第240行开始
CFE version 1.0.37-10.3 for BCM96358 (32bit,SP,BE)
...
天涯 发表于 2009-4-12 21:16 https://www.chinadsl.net/images/common/back.gif
怎么刷的阿？用JTAG了吗？
用TTL数据线,第一次在CFE状态下刷,第二次在系统启动后才能刷(UPDATE SOFTWARE),两次都刷了带CFE的固件.但我的RG100A-AA不能够正确的启动 楼上我贴出引导记录了.
很快就发个128K的
本帖最后由 天涯 于 2009-4-13 13:24 编辑
http://gltianya.googlepages.com/1.5-128k.rar
http://gltianya.googlepages.com/1.5-cfe-128k.rar
楼主安心做开发及修改BUG,封包如果我没有理解错的话,我已经做好了.这些体力活就让我这等菜鸟代劳吧.
128k的是不是可以直接在网页上刷了?
http://gltianya.googlepages.com/1.5-128k.rar
http://gltianya.googlepages.com/1.5-cfe-128k.rar
楼主安心做开发及修改BUG,封包如果我没有理解错的话,我已经做好了.这些体力活就让我这等菜鸟代劳吧.
天涯 发表于 2009-4-13 12:48 https://www.chinadsl.net/images/common/back.gif
1.5-128k的是不是不带CFE的啊？可以不用TTL线直接刷吗？